Manual Microlife OXY 210 (page 6 of 75) (English, German, Dutch, French, Italian, Portuguese, Turkish, Spanish)

773555

Zoom out

Zoom in

1/75

The device must be able to measure the pulse

properly to obtain an accurate SpO2 measure-

ment. Verify that nothing is hindering the pulse

measurement before relying on the SpO2

measurement.

The maximum application time at a single site

should be less than 30 minutes, in order to

ensure correct sensor alignment and skin integ-

rity.

Inaccurate measurements may occur if:

The patient suffers from significant levels of dysfunc-

tional hemoglobin (such as carboxyhemoglobin or

methemoglobin).

Intravascular dyes such as indocyanine green or meth-

ylene blue have been injected into the patient.

Used in the presence of high ambient light (e.g. direct

sunlight). Shield the sensor area with a surgical towel if

necessary.

There is excessive patient movement.

The patient experiences venous pulsations.

The patient has hypotension, severe vasoconstriction,

severe anemia, or hypothermia.

The patient is in cardiac arrest or is in shock.

Fingernail polish or false fingernails are applied.

6. Inserting the batteries

After you have unpacked your device, first insert the

batteries. The battery compartment is on the bottom of the

device. Remove the battery cover by sliding it in the direc-

tion shown. Insert the batteries (2 x 1.5 V, size AAA),

thereby observing the indicated polarity.

Replace the batteries when the low power indi-

cator 5 appears on the display.

Always replace both batteries at the same time.

7. ON/OFF button

/ Function button

Press and release the ON/OFF button 1 to turn on, hold

the button for about one second. The device shows the

settings menu AT. Press or hold the ON/OFF button to

perform corresponding operations. Hold it to set an item, or

press it to switch an option or switch the display mode.

Press means no more than 0.5 seconds, while hold means

more than 0.5 seconds.

Alert Sound Setting

Hold ON/OFF button 1 while the device is switched

on.Settings menu (interface 1) is displayed AT-a. Move «*»

to the corresponding option, and hold the function button to

set Alm to on and set Beep to off. When Alm is set to on

and the measured values of the blood oxygen saturation

and pulse rate go beyond the upper limit or lower limit, the

device gives off an alert sound. When Beep is set to on, a

tick will be heard along with pulse beats during pulse rate

measurement. While the «*» symbol stays on the Restore

option, hold the functional button to restore default settings.

Brightness Setting

Press ON/OFF button 1 to select the Brightness option

and then hold the ON/OFF button to set the brightness to a

value ranging from 1 to 5. The greater the value, the

greater the brightness of the screen.

Alert Range Setting

On settings menu (interface 2) AT-b, press the ON/OFF

button 1 to switch between options. On this interface, you

can set the upper limit and lower limit of SpO2 Alm and PR

Alm. While the «*» symbol stays on the +/- option, hold the

functional button to set the option to + or -.

In + mode, select the corresponding option and hold the

ON/OFF button to increase the upper or lower limit; in -

mode, hold the ON/OFF button to decrease the upper or

lower limit. Move «*» to the Exit option, and hold the ON/

OFF button to return to the monitoring interface.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Microlife OXY 210 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 1.07 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Microlife OXY 210 Manual

Product: