536862

Microlife NC 150 Manual

5
Zoom out
Zoom in
Previous page
1/60
Next page
3NC 150
EN
Ready for measuring
AK
:
When the unit is ready for measuring,
the «
°C
» or «
°F
» icon will keep flashing while the mode icon
(body or object) will be displayed.
Measurement complete AL: The reading will be shown on the
display 3 with the «°C» or «°F» icon and the mode icon
steady. The unit is ready for the next measurement as soon as
the «°C» or «°F» icon is flashing again.
Low battery indicator AO: When the unit is turned on, the «»
icon will keep flashing to remind the user to replace the battery.
5. Setting Date, Time and Beeper Functions
Setting the date and time
1. After the new batteries are fitted, the year number flashes in the
display BP. You can set the year by pressing the START button
4. To confirm and then set the month, press the M-button 8.
2. Press the START button 4 to set the month. Press the M-
button 8 to confirm and then set the day.
3. Follow the instructions above to set the day, 12 or 24 hour
mode, hours and minutes.
4. Once you have set the minutes and pressed the M-button 8,
the date and time are set and the time is displayed.
If no button is pressed for 20 seconds, the device automat-
ically switches to ready for measuring AK.
Cancel time setup: Press the ON/OFF button 5 during
time setup. The LCD will show Date/Time icons with «--:--».
After that press the ON/OFF button 5 to start the measure-
ment. If no further action is taken within 20 seconds, the
device will automatically turn off.
Change current date and time: Press and hold the M-
button 8 for approx. 3 seconds until the year number
starts to flash BP. Now you can enter the new values as
described above.
Setting the beeper
1. When the device is switched off, press and hold the ON/OFF
button 5 for 5 seconds to set the beeper BQ.
2. Press the ON/OFF button 5 again to either turn the beeper on
or off. The beeper is activated when the beeper icon BQ is not
crossed-out.
If no button is pressed for 5 seconds, the device automati-
cally switches to ready for measuring AK.
6. Changing between Body and Object Mode
For changing from body to object mode, slide the mode switch 6
at the side of the thermometer downwards. For switching back to
body mode, slide the switch up again.
7. Directions for Use
Measuring in body mode
1. Press the ON/OFF button 5. The display 3 is activated to
show all segments for 1 second.
2. When the «°C» or «°F» icon is flashing, a beep sound is heard
and the thermometer is ready for measuring AK.
3. Aim the thermometer at the center of the forehead with a
distance of no more than 5 cm. Please remove any hair,
sweat or dirt from the forehead before measuring to improve the
accuracy of the readings.
4. Press the START button 4 and steadily move the ther-
mometer from the middle of the forehead to the temple area
(about 1 cm above the eyebrow). The activated blue tracking
light will indicate the area being measured. After 3 seconds a
long beep will verify the completion of measurement. If the
temple area hasn’t been reached before the long beep is heard,
repeat the measurement as described above, but move the
thermometer a little faster.
5. Read the recorded temperature from the LCD display.
Measuring in object mode
1. Follow steps 1-2 above, then aim the thermometer at the center
of the object you want to measure with a distance of no more
than 5 cm. Press the START button 4. After 3 seconds a long
beep will verify the completion of measurement.
2. Read the recorded temperature from the LCD display.
NOTE:
Patients and thermometer should stay in similar room
condition for at least 30 minutes.
Don't take a measurement while or immediately after nursing a
baby.
Don't use the thermometer in high humidity environments.
Patients should not drink, eat or exercise before/while taking
the measurement.
Don't move the measurement device from the measuring area
before hearing the termination beep.
10 short beeps and a red LCD backlight alerts the patient that
he/she may have a temperature equal to or higher than 37.5 °C.
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Microlife NC 150 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Microlife NC 150 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 3,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info