Manual Microlife IR 150 (page 5 of 55) (English, Danish, Swedish, Norwegian, Finnish)

536861

Zoom out

Zoom in

1/55

3IR 150

Measurements taken from the surrounding tissue of the ear canal

generate lower readings and may result in misdiagnosis of fever.

To avoid an inaccurate measurement

1. Switch on the thermometer by pressing the ON/OFF button 4.

2. After one beep is heard (and the temperature scale icon is

flashing), straighten the ear canal by gently pulling the middle

of the ear back and up.

3. Place the probe 1 firmly into the ear canal, press the START

button 3 and keep the probe in the ear until the thermometer

beeps to signal the completion of the measurement.

4. Control Displays and Symbols

 All segments displayed 7: Press the ON/OFF button 4 to

turn on the unit; all segments will be shown for 1 second.

 Ready for measurement 9: When the unit is ready for

measurement, the «°C» or «°F» icon will keep flashing.

The probe LED light is activated for 10 seconds.



Measurement complete

The reading will be shown on the

display

with the «

°C

» or «

°F

» icon; the unit is ready for the

next measurement, when the «

°C

» or «

°F

» icon is flashing again.

 Out-of-ear temperature indication AK: A crossed-ear-icon will

appear on the display 2 if the reading falls outside the range

32.0  42.2 °C / 89.6  108.0 °F.

 Low battery indicator AL: When the unit is turned on, the «»

icon will keep flashing to remind the user to replace the battery.

5. Setting Date, Time and Beeper Functions

Setting the date and time

1. After the new battery is fitted, the year number flashes in the

display

. You can set the year by pressing the START button

To confirm and then set the month, press the M-button

2. Press the START button 3 to set the month. Press the M-

button 6 to confirm and then set the day.

3. Follow the previously mentioned instructions to set the day, 12

or 24 hour mode, hours and minutes.

4. Once you have set the minutes and pressed the M-button 6,

the date and time are set and the time is displayed.



If no button is pressed for 20 seconds, the device automat-

ically switches to ready for measuring 9.



Cancel time setup: Press the ON/OFF button 4 during

time setup. The LCD will show Date/Time icons with «--:--».

After that press the ON/OFF button 4 to start the measure-

ment. If no further action is taken within 60 seconds, the

device will automatically turn off.



Change current date and time: Press and hold the M-

button 6 for approx. 3 seconds until the year number

starts to flash BN. Now you can enter the new values as

described above.

Setting the beeper

1. When the device is switched off, press and hold the ON/OFF

button 4 for 5 seconds to set the beeper BO.

2. Press the ON/OFF button 4 again to either turn the beeper on

or off. The beeper is activated when the beeper icon BO is not

crossed-out.



If no button is pressed for 5 seconds, the device automati-

cally switches to ready for measuring 9.

6. Directions for Use

1. Press the ON/OFF button 4. The display 2 is activated to

show all segments for 1 second.

2. When the «°C» or «°F» icon is flashing, a beep sound is heard

and the thermometer is ready for measuring 9.

3. The probe LED light is activated and will automatically turn off

after 10 seconds.

4. Straighten the ear canal by pulling the ear up and back to give

a clear view of the eardrum.

 For children under 1 year; pull the ear straight back.

 For children of 1 year to adult; pull the ear up and back.

Also refer to the short instructions at the front.

5. While gently pulling the ear, insert the probe snugly into the ear

canal

(about 1 sec.)

and

immediately

press the START button

. Release the button and wait for the beep sound. This indicates

the end of the measurement.

6. Remove the thermometer from the ear canal. The display shows

the measured temperature



NOTE:

 To ensure accurate readings, wait at least 30 sec. after 3-5

continuous measurements.

 Accumulation of ear wax on the probe can result in less accu-

rate temperature readings or cross infection between users.



It is essential that the probe is cleaned after every measure-

ment.

Therefore, this device reminds the user to clean the probe

when turning off the device. «CLEAN ME»

is displayed and

the probe LED light will flash for 3 seconds. For cleaning, follow

the instructions in the «Cleaning and Disinfecting» section.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Microlife IR 150 in the language / languages: English, Danish, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 2,61 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Microlife IR 150 Manual

Product: