Manual Microlife BP W150 IMT (page 38 of 133) (English)

536847

Zoom out

Zoom in

1/133

Listening to your system

Listening with Acoustic Calibration EQ

•

Default setting: ON

You can listen to sources using the Acoustic Calibration

Equalization set in Automatically setting up for surround

sound (MCACC) on page 23. Refer to these pages for more on

Acoustic Calibration Equalization.

See Setting the Audio options

on page 40.

The MCACC indicator on the front panel lights when Acoustic

Calibration EQ is active.

You can’t use Acoustic Calibration EQ with Stream Direct

mode and it has no effect with headphones.

Better sound using Phase Control

•

Default setting: ON

This receiver’s Phase Control feature uses phase correction

measures to make sure your sound source arrives at the

listening position in phase, preventing unwanted distortion

and/or coloring of the sound.

Phase Control technology provides coherent sound

reproduction through the use of phase matching for an

optimal sound image at your listening position. The default

setting is on and we recommend leaving Phase Control

switched on for all sound sources.



While listening to a source, press , then press

PHASE

to switch the P.CTL (Phase Control) ON or OFF.

Note

•

Phase matching is a very important factor in achieving

proper sound reproduction. If two waveforms are ‘in phase’,

they crest and trough together, resulting in increased

amplitude, clarity and presence of the sound signal. If a

crest of a wave meets a trough, then the sound will be ‘out

of phase’ and an unreliable sound image will be produced.

•

If your subwoofer has a phase control switch, set it to the

plus (+) sign (or 0°). However, the effect you can actually

feel when Phase Control is set to ON on this receiver

depends on the type of your subwoofer. Set your subwoofer

to maximize the effect. It is also recommended you try

changing the orientation or the place of your subwoofer.

•

Set the built-in lowpass filter switch of your subwoofer to

OFF. If this cannot be done on your subwoofer, set the

cutoff frequency to a higher value.

•

If the speaker distance is not properly set, you may not have

a maximized Phase Control effect.

•

The Phase Control mode cannot be set to ON in the

following cases:

When the PURE DIRECT mode is switched on.

When the headphones are connected.

Using surround back channel processing (VSX-

S510 only)

You can have the receiver automatically use 6.1 or 7.1

decoding for 6.1 encoded sources (for example, Dolby Digital

EX or DTS-ES), or you can choose to always use 6.1 or 7.1

decoding (for example, with 5.1 encoded material). With 5.1

encoded sources, a surround back channel will be generated,

but the material may sound better in the 5.1 format for which

it was originally encoded (in which case, you can simply

switch surround back channel processing off).

•

With a 7.1-channel surround system, audio signals that

have undergone matrix decoding processing through

surround back channel processing to which the Up Mix

function is added are output from the surround back

speakers.



Press , then press

SB CH

repeatedly to cycle

the surround back channel options.

Each press cycles through the options as follows:

•

SB ON – Matrix decoding processing for generating

the surround back component from the surround

component is turned on.

•

SB AUTO – Matrix decoding processing for generating

the surround back component from the surround

component is switched automatically. Matrix

decoding processing is only performed when surround

back channel signals are detected in the input signals.

•

SB OFF – Matrix decoding processing for generating

the surround back component from the surround

component is turned off.

RECEIVER

Really enjoyed this post.Really thank you! Keep writing. makaberzux Submitted on 5-8-2022 at 13:42
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Microlife BP W150 IMT in the language / languages: English as an attachment in your email.

The manual is 4,09 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Microlife BP W150 IMT

Microlife BP W150 IMT User Manual - English, German, Dutch, Danish, French, Italian, Swedish, Norwegian, Finnish - 133 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Microlife BP W150 IMT Manual

Product: