Manual Microlife BP B2 BASIC (page 22 of 81) (English, German, Dutch, French, Italian, Portuguese, Turkish, Spanish)

773467

Zoom out

Zoom in

1/81

IB BP B2 Basic S-V11 1221 Revision Date: 2021-02-04

BPB2 Basic

Blood Pressure Monitor

FA 74Preparation

Sit on a back-supported chair and keep your legs uncrossed. / Siéntese en una silla con

respaldo y mantenga las piernas descritas. / Asseyez-vous sur une chaise (avec dossier)

et ne croisez pas les jambes. / Sedere su una sedia con schienale e non accavallare le

gambe. / Setzen Sie sich auf einen Stuhl mit Rückenlehnen und kreuzen Sie die Beine

nicht. / Arkası destekli bir sandalyeye oturunuz ve bacak bacak üzerine atmayınız. /

Sente-se numa cadeira com encosto e não cruze as pernas. /

Ga op een stoel zitten

met rugleuning en kruis uw benen niet. / Καθίστε σε καρέκλα με πλάτη και

μην σταυρώνετε τα πόδια σας. /

Fit the cuff closely, but not too tight. / Ajuste el brazalete de cerca, pero no demasiado

apretado. / Ajustez le brassard mais ne pas trop serrer. / Indossare il bracciale e

stringerlo, ma non troppo. / Legen Sie die Manschette eng aber nicht zu stramm an.

/ Manşonu yakın bir şekilde kapatınız ancak çok sıkmayınız. / Aperte corretamente

a braçadeira, mas não demasiado.

/ Breng de manchet aan rondom uw arm,

maar niet te strak. / Τοποθετήστε την περιχειρίδα εφαρμοστά αλλά όχι πολύ

σφιχτά. /

Avoid thick or close-fitting garments on the upper arm. / Evite prendas gruesas o

ajustadas en la parte superior del brazo. / Évitez les vêtements épais ou ajustés sur

le haut du bras. / Evitare di indossare abiti pesanti o aderenti intorno al braccio. /

Vermeiden Sie dicke oder eng anliegende Kleidungsstücke am Oberarm. / Kolun üst

kısmında sıkan ve dar giysilerden uzak durunuz. / Evite usar roupa grossa ou justa no

braço. / Vermijd dikke of strak zittende kleding aan uw bovenarm.

/ Αποφύγετε να

φοράτε χοντρά ή στενά ενδύματα στο μπράτσο σας. /

Place the artery-mark on the cuff over your artery. / Coloque la marca de la arteria en

el brazalete sobre su arteria. / Placez le repère d'artère du brassard au niveau de votre

artère. / Posizionare l’indicatore giallo dell’arteria posto sul bracciale in corrispondenza

dell’arteria del braccio./ Platzieren Sie die Arterienmarkierung auf der Manschette über

Ihrer Arterie. / Manşonun üzerindeki arter işaretinini, kolunuzun üzerindeki artere denk

getiriniz. / Coloque a marca existente na braçadeira sobre a artéria do braço

. / Plaats

de manchet met arteriemarkering op uw arterie. / Τοποθετήστε την ένδειξη

αρτηρίας που βρίσκεται στην περιχειρίδα πάνω από την αρτηρία σας. /

Position the cuff 1-2 cm above your elbow. / Coloque el brazalete 1-2 cm por

encima del codo. / Installez le brassard 1 à 2 cm au dessus de la pliure du coude.

/ Posizionare il bracciale 1-2 cm sopra il gomito. / Positionieren Sie die Manschette

1-2 cm über Ihrem Ellbogen. / Manşonu dirseğinizden 1-2 cm yukarıya yerleştirin. /

Coloque a braçadeira 1-2 cm acima do cotovelo

. / Positioneer de manchet

1-2

cm boven uw elleboog. / Τοποθετήστε την περιχειρίδα

1-2

εκατοστά πάνω

από τον αγκώνα σας. /

Keep your arm still and do not speak during the measurement. / Mantenga su brazo quieto

y no hable durante la medición. / Ne pas parler et ne pas bouger votre bras pendant la

prise de mesure. / Tenere il braccio fermo e non parlare durante la misurazione. / Halten Sie

Ihren Arm ruhig und sprechen Sie während der Messung nicht. / Kolunuzu sabit tutunuz ve

ölçüm sırasında konuşmayınız. / Mantenha o braço imóvel e não fale durante a medição.

/ Houd uw arm stil en spreek niet tijdens de meting. / Κρατήστε το χέρι σας

ακίνητο και μην μιλάτε κατά τη διάρκεια της μέτρησης. /



















1-2



- 





EC REP Microlife UAB

P. Lukšio g. 32

08222 Vilnius / Lithuania

Microlife AG,

Espenstrasse 139

9443 Widnau / Switzerland

www.microlife.com

Microlife BP B2 Basic Microlife BP B2 BasicMicrolife BP B2 Basic Guarantee CardBefore each measurement

Avoid eating, bathing, smoking or caffeine (approx. 30 min).

Evite comer, bañarse, fumar o cafeína (aproximadamente 30 minutos).

Évitez de manger, de vous baigner, de fumer ou do consommer des produits contenant de la

caféine pendant environ 30 minutes.

Evitare di mangiare, fare il bagno, fumare o bere caffè (almeno 30 min.)

Vermeiden Sie essen, baden, rauchen oder Koffein (ca. 30 min).

Yeme, içme, duş alma, sigarak içme ve kefeinden uzak durunuz (yaklaşık 30 dak.)

Evite comer, tomar banho, fumar ou ingerir cafeína (cerca de 30 min).

Vermijd eten, baden, roken of het nuttigen van caffeine (ca. 30 minuten).

Αποφύγετε τη κατανάλωση φαγητού, το μπάνιο, το κάπνισμα ή την καφεΐνη (περίπου 30 λεπτά)







Avoid activity and relax for 5-10 min.

Evite la actividad y relájese durante 5-10 min.

Évitez toute activité et détendez-vous pendant 5 à 10 min

Evitare di fare attività fisica e rilassarsi per 5-10 minuti.

Vermeiden Sie Bewegung und entspannen Sie sich für 5-10 Min.

Spordan kaçınınız ve 5-10 dakika dinlenmiş olunuz.

Evite a atividade física e relaxe 5-10 min.

Vermijd beweging en ontspan voor 5-10 minuten.

Αποφύγετε τη σωματική δραστηριότητα και χαλαρώστε για 5-10 λεπτά



5-10





Measure before medication intake.

Mida antes de tomar medicamentos.

Ne pas prendre de médicament avant de mesurer votre tension.

Effettuare la misurazione prima di assumere farmaci.

Messen Sie bevor Sie Medikamente einnehmen.

İlaç alımından önce ölçüm yapınız.

Proceda à medição antes de tomar medicação.

Meet alvorens u medicatie inneemt.

Πραγματοποιήστε τη μέτρηση πριν από τη λήψη φαρμάκων





Name of Purchaser / Nombre del comprador/

Nom de l'acheteur / Nome del rivenditore / Name

des Käufers / Alıcının adı / Nome do comprador /

Naam koper / Ονοματεπώνυμο αγοραστή /

Serial Number / Número de serie/ Numéro

de série / Numero di serie / Serien-Nr. / Seri

numarası / Número de série / Serienummer /

Αριθμός σειράς / /

Date of Purchase / Fecha de compra/ Date

d'achat / Data d’acquisto / Kaufdatum / Satın

alma tarihi / Data da compra / Datum van

aankoop / Ημερομηνία αγοράς / /

Specialist Dealer / Distribuidor especializado/

Revendeur / Categoria rivenditore / Fachhändler /

Uzman satıcı / Revendedor autorizado / Specialist

Dealer / Εξειδικευμένος αντιπρόσωποςa /

١٢ ARﺔﻟﺎﻔﻜﻟا ﺔﻗﺎﻄﺑ

(ﻲﻔﻠﺨﻟا ءﺎﻄﻐﻟا ﺮﻈﻧا) ﺔﻟﺎﻔﻜﻟا ﺔﻗﺎﻄﺑ

:يﺮﺘﺸﻤﻟا ﻢﺳا

:ﻞﻳدﻮﻤﻟا

:ﻞﺴﻠﺴﺘﻟا ﻢﻗر

:ءاﺮﺸﻟا ﺦﻳرﺎﺗ

:ﺺﺘﺨﻤﻟا ﺮﺟﺎﺘﻟا

١٢ ARﺔﻟﺎﻔﻜﻟا ﺔﻗﺎﻄﺑ

(ﻲﻔﻠﺨﻟا ءﺎﻄﻐﻟا ﺮﻈﻧا) ﺔﻟﺎﻔﻜﻟا ﺔﻗﺎﻄﺑ

:يﺮﺘﺸﻤﻟا ﻢﺳا

:ﻞﻳدﻮﻤﻟا

:ﻞﺴﻠﺴﺘﻟا ﻢﻗر

:ءاﺮﺸﻟا ﺦﻳرﺎﺗ

:ﺺﺘﺨﻤﻟا ﺮﺟﺎﺘﻟا

١٢ ARﺔﻟﺎﻔﻜﻟا ﺔﻗﺎﻄﺑ

(ﻲﻔﻠﺨﻟا ءﺎﻄﻐﻟا ﺮﻈﻧا) ﺔﻟﺎﻔﻜﻟا ﺔﻗﺎﻄﺑ

:يﺮﺘﺸﻤﻟا ﻢﺳا

:ﻞﻳدﻮﻤﻟا

:ﻞﺴﻠﺴﺘﻟا ﻢﻗر

:ءاﺮﺸﻟا ﺦﻳرﺎﺗ

:ﺺﺘﺨﻤﻟا ﺮﺟﺎﺘﻟا

١٢ ARﺔﻟﺎﻔﻜﻟا ﺔﻗﺎﻄﺑ

(ﻲﻔﻠﺨﻟا ءﺎﻄﻐﻟا ﺮﻈﻧا) ﺔﻟﺎﻔﻜﻟا ﺔﻗﺎﻄﺑ

:يﺮﺘﺸﻤﻟا ﻢﺳا

:ﻞﻳدﻮﻤﻟا

:ﻞﺴﻠﺴﺘﻟا ﻢﻗر

:ءاﺮﺸﻟا ﺦﻳرﺎﺗ

:ﺺﺘﺨﻤﻟا ﺮﺟﺎﺘﻟا







1BP B2 Basic EN

Display

Read the instructions carefully before using this device.

Type BF applied part

Intended use:

This oscillometric blood pressure monitor is intended for

measuring non-invasive blood pressure in people aged 12 years or

older.

It is clinically validated in patients with hypertension, hypotension,

diabetes, pregnancy, pre-eclampsia, atherosclerosis, end-stage

renal disease, obesity and the elderly.

Dear Customer,

This device was developed in collaboration with physicians and

clinical tests carried out prove its measurement accuracy to be of

a very high standard.*

If you have any questions, problems or want to order spare parts

please contact your local Microlife-Customer Service. Your dealer

or pharmacy will be able to give you the address of the Microlife

dealer in your country. Alternatively, visit the internet at

www.microlife.com where you will find a wealth of invaluable infor-

mation on our products.

Stay healthy – Microlife AG!

* This device uses the same measuring technology as the award

winning «BP 3BTO-A» model tested according to the British and

Irish Hypertension Society (BIHS) protocol.

Table of Contents

1. Using the Device for the First Time

• Inserting the batteries

• Setting the date and time

• Selecting the correct cuff

2. Checklist for Taking a Reliable Measurement

3. Taking a Blood Pressure Measurement

• Manual inflation

• How not to store a reading

• How do I evaluate my blood pressure?

• Appearance of the Irregular Heartbeat (IHB) Symbol

4. Data Memory

• Viewing the stored values

• Clearing all values

5. Battery Indicator and Battery change

Microlife BP B2 Basic EN

1ON/OFF button

2Display

3M-button (memory)

4Time Button

5Cuff Socket

6Mains Adapter Socket

7Battery Compartment

8Cuff

9Cuff Connector

AT Cuff Tube

AK Systolic Value

AL Diastolic Value

AM Pulse Rate

AN Battery Display

AO Traffic Light Indicator

AP Stored Value

AQ Pulse Indicator

AR Cuff Fit Check

-A: Suboptimal Cuff Fit

-B: Arm Movement Indicator «Err 2»

-C: Cuff Pressure Check «Err 3»

AS Cuff Signal Indicator «Err 1»

BT Irregular Heartbeat (IHB) Symbol

BK Date/Time

Keep dry

• Low battery

• Flat battery – replacement

• Which batteries and which procedure?

• Using rechargeable batteries

6. Using a Mains Adapter

7. Error Messages

8. Safety, Care, Accuracy Test and Disposal

• Safety and protection

• Device care

• Cleaning the cuff

• Accuracy test

• Disposal

9. Guarantee

10. Technical Specifications

Guarantee Card (see Back Cover)

1. Using the Device for the First Time

Inserting the batteries

After you have unpacked your device, first insert the batteries. The

battery compartment 7 is on the bottom of the device. Insert the

batteries (4 x 1.5 V, size AA), thereby observing the indicated

polarity.

Setting the date and time

1. After the new batteries are fitted, the year number flashes in the

display. You can set the year by pressing the M-button 3. To

confirm and then set the month, press the time button 4.

2. Press the M-button to set the month. Press the time button to

confirm and then set the day.

3. Follow the instructions above to set the day, hour and minutes.

4. Once you have set the minutes and pressed the time button, the

date and time are set and the time is displayed.

5. If you want to change the date and time, press and hold the time

button down for approx. 3 seconds until the year number starts

to flash. Now you can enter the new values as described above.

Selecting the correct cuff

Microlife offers different cuff sizes. Select the cuff size to match the

circumference of your upper arms (measured by close fitting in the

centre of the upper arm).

Pre-shaped cuffs are optionally available.

Only use Microlife cuffs.



Contact your local Microlife Service if the enclosed cuff 8 does

not fit.



Connect the cuff to the device by inserting the cuff connector 9

into the cuff socket 5 as far as it will go.

2. Checklist for Taking a Reliable Measurement



Avoid activity, eating or smoking immediately before the

measurement.



Sit down on a back-supported chair and relax for 5 minutes.

Keep the feet flat on the floor and do not cross your legs.



Always measure on the same arm (normally left). It is recom-

mended that doctors perform double arm measurements on a

patients first visit in order to determine which arm to measure in

the future. The arm with the higher blood pressure should be

measured.



Remove close-fitting garments from the upper arm. To avoid

constriction, shirt sleeves should not be rolled up - they do not

interfere with the cuff if they are laid flat.



Always ensure that the correct cuff size is used (marking on the

cuff).

Fit the cuff closely, but not too tight.



Make sure that the cuff is positioned 1-2 cm above the elbow.

The artery mark on the cuff (ca. 3 cm long bar) must lie over

the artery which runs down the inner side of the arm.

Support your arm so it is relaxed.

Ensure that the cuff is at the same height as your heart.

3. Taking a Blood Pressure Measurement

1. Press the ON/OFF button 1 to start the measurement.

2. The cuff will now pump up automatically. Relax, do not move

and do not tense your arm muscles until the measurement

result is displayed. Breathe normally and do not talk.

Cuff size for circumference of upper arm

S 17 - 22 cm

M 22 - 32 cm

M - L 22 - 42 cm

L 32 - 42 cm

L - XL 32 - 52 cm

3BP B2 Basic EN

3. The cuff fit check AR on the display indicates that the cuff is

perfectly placed. If the icon AR-A appears, the cuff is fitted

suboptimally, but it is still ok to measure.

4. When the correct pressure is reached, the pumping stops and

the pressure falls gradually. If the required pressure was not

reached, the device will automatically pump some more air into

the cuff.

5. During the measurement, the pulse indicator AQ flashes in the

display.

6. The result, comprising the systolic AK and the diastolic AL blood

pressure and the pulse rate AM is displayed. Note also the

explanations on further display symbols in this booklet.

7. When the device has finished measuring, remove the cuff.

8. Switch off the device. (The monitor does switch off automati-

cally after approx. 1 min.).

You can stop the measurement at any time by pressing the

ON/OFF button (e.g. if you feel uneasy or an unpleasant

pressure sensation).

This monitor is specially tested for use in pregnancy and

pre-eclampsia. When you detect unusual high readings in

pregnancy, you should measure after a short while again

(eg. 1 hour). If the reading is still too high, consult your

doctor or gynecologist.

Manual inflation

In case of high systolic blood pressure (e.g. above 135

mmHg), it can be an advantage to set the pressure individually.

Press the ON/OFF button after the monitor has been pumped up

to a level of approx. 30 mmHg (shown on the display). Keep the

button pressed until the pressure is about 40 mmHg above the

expected systolic value – then release the button.

How not to store a reading

As soon as the reading is displayed press and hold the ON/OFF

button 1 until «M» AP is flashing. Confirm to delete the reading by

pressing the Time button 4.

«CL» is displayed when the reading is deleted from the

memory successfully.

How do I evaluate my blood pressure?

The triangle on the left-hand edge of the display AO points at the

range within which the measured blood pressure value lies. The

value is either within the optimum (white), elevated (hatched gray)

or high (black) range. The classification corresponds to the

following ranges defined by international guidelines (ESH, ESC,

JSH). Data in mmHg.

The higher value is the one that determines the evaluation.

Example: a blood pressure value of 140/80 mmHg or a value of

130/90 mmHg indicates «blood pressure too high».

Appearance of the Irregular Heartbeat (IHB) Symbol

This symbol BT indicates that an irregular heartbeat was detected.

In this case, the measured blood pressure may deviate from your

actual blood pressure values. It is recommended to repeat the

measurement.

4. Data Memory

This device automatically stores the last 30 measurement values.

Viewing the stored values

Press the M-button 3 briefly, when the device is switched off. The

display first shows «M» AP and «A», which stands for the average

of all stored values.

Pressing the M-button again displays the previous value. Pressing

the M-button repeatedly enables you to move from one stored

value to another.

Blood pressure readings with suboptimal cuff fit AR-A are

not considered in the average value.

Pay attention that the maximum memory capacity of 30

memories is not exceeded. When the 30 memory is full,

the oldest value is automatically overwritten with the 31

value. Values should be evaluated by a doctor before the

memory capacity is reached – otherwise data will be lost.

Range Systolic Diastolic Recommendation

1. blood pressure

too high

≥135 ≥85 Seek medical

advice

2. blood pressure

elevated

130 - 134 80 - 84 Self-check

3. blood pressure

normal

<130 <80 Self-check

Information for the doctor in case of repeated appearance of

the IHB symbol:

This device is an oscillometric blood pressure monitor that also

measures the pulse during blood pressure measurement and

indicates when the heart rate is irregular.

Clearing all values

If you are sure that you want to permanently remove all stored

values, hold down the M-button (the device must have been

switched off beforehand) until «CL ALL» appears and then

release the button. To permanently clear the memory, press the

Time button while «CL ALL» is flashing. Individual values cannot

be cleared.

Cancel deletion: press ON/OFF button 1 while «CL

ALL» is flashing.

5. Battery Indicator and Battery change

Low battery

When the batteries are approximately ¾ empty the battery symbol

AN will flash as soon as the device is switched on (partly filled

battery displayed). Although the device will continue to measure

reliably, you should obtain replacement batteries.

Flat battery – replacement

When the batteries are flat, the battery symbol AN will flash as soon

as the device is switched on (flat battery displayed). You cannot

take any further measurements and must replace the batteries.

1. Open the battery compartment 7 at the back of the device.

2. Replace the batteries – ensure correct polarity as shown by the

symbols in the compartment.

3. To set date and time, follow the procedure described in

«Section 1.».

The memory retains all values although date and time must

be reset – the year number therefore flashes automatically

after the batteries are replaced.

Which batteries and which procedure?

Use 4 new, long-life 1.5 V, size AA alkaline batteries.

Do not use batteries beyond their date of expiry.

Remove batteries if the device is not going to be used for a

prolonged period.

Using rechargeable batteries

You can also operate this device using rechargeable batteries.

Only use «NiMH» type reusable batteries.

Batteries must be removed and recharged when the flat

battery symbol appears. They should not remain inside the

device as they may become damaged (total discharge as a

result of low use of the device, even when switched off).

Always remove the rechargeable batteries if you do not

intend to use the device for a week or more.

Batteries cannot be charged in the blood pressure monitor.

Recharge batteries in an external charger and observe the

information regarding charging, care and durability.

6. Using a Mains Adapter

You can operate this device using the Microlife mains adapter (DC

6V, 600 mA).

Only use the Microlife mains adapter available as an orig-

inal accessory appropriate for your supply voltage.

Ensure that neither the mains adapter nor the cable are

damaged.

1. Plug the adapter cable into the mains adapter socket 6 in the

blood pressure monitor.

2. Plug the adapter plug into the wall socket.

When the mains adapter is connected, no battery current is

consumed.

7. Error Messages

If an error occurs during the measurement, the measurement is

interrupted and an error message, e.g. «Err 3», is displayed.

Error

Description

Potential cause and remedy

Err 1

Signal too

weak

The pulse signals on the cuff are too

weak. Re-position the cuff and repeat the

measurement.*

Err 2

AR-B Error signal During the measurement, error signals

were detected by the cuff, caused for

instance by movement or muscle

tension. Repeat the measurement,

keeping your arm still.

Err 3

AR-C Abnormal

cuff pres-

sure

An adequate pressure cannot be gener-

ated in the cuff. A leak may have

occurred. Check that the cuff is correctly

connected and is not too loose. Replace

the batteries if necessary. Repeat the

measurement.

5BP B2 Basic EN

* Please immediately consult your doctor, if this or any other

problem occurs repeatedly.

8. Safety, Care, Accuracy Test and Disposal

Safety and protection

Follow instructions for use. This document provides important

product operation and safety information regarding this device.

Please read this document thoroughly before using the device

and keep for future reference.

This device may only be used for the purposes described in

these instructions. The manufacturer cannot be held liable for

damage caused by incorrect application.

This device comprises sensitive components and must be

treated with caution. Observe the storage and operating condi-

tions described in the «Technical Specifications» section.

Protect it from:

- water and moisture

- extreme temperatures

- impact and dropping

- contamination and dust

- direct sunlight

- heat and cold

The cuffs are sensitive and must be handled with care.

Do not exchange or use any other kind of cuff or cuff connector

for measuring with this device.

Only pump up the cuff once fitted.

Do not use this device close to strong electromagnetic fields

such as mobile telephones or radio installations. Keep a

minimum distance of 3.3 m from such devices when using this

device.

Do not use this device if you think it is damaged or notice

anything unusual.

Never open this device.

If the device is not going to be used for a prolonged period the

batteries should be removed.

Read the additional safety information provided within the indi-

vidual sections of this instruction manual.

If you suffer from a cardiac arrhythmia consult with your doctor

before using the device. See also chapter «Appearance of the

Irregular Heartbeat (IHB) Symbol» of this user manual.

The measurement results given by this device is not a diag-

nosis. It is not replacing the need for the consultation of a physi-

cian, especially if not matching the patient’s symptoms. Do not

rely on the measurement result only, always consider other

potentially occurring symptoms and the patient’s feedback.

Calling a doctor or an ambulance is advised if needed.

Permanently high blood pressure values can damage your

health and must be treated by your doctor!

Always discuss your values with your doctor and tell him/her if

you have noticed anything unusual or feel unsure. Never rely

on single blood pressure readings.

Under no circumstances should you alter the dosages of

drugs or initiate a treatment without consulting your

doctor.

Deviations between measurements taken by your doctor or in

the pharmacy and those taken at home are quite normal, as

these situations are completely different.

The pulse display is not suitable for checking the

frequency of heart pacemakers!

If you are pregnant, you should monitor your blood pressure

regularly as it can change drastically during this time.

Ensure that children do not use this device unsupervised;

some parts are small enough to be swallowed. Be aware of

the risk of strangulation in case this device is supplied with

cables or tubes.

Device care

Clean the device only with a soft, dry cloth.

Cleaning the cuff

The cuff delivered with this device is washable.

Err 5

Abnormal

result

The measuring signals are inaccurate

and no result can therefore be displayed.

Read through the checklist for

performing reliable measurements and

then repeat the measurement.*

Pulse or

cuff pres-

sure too

high

The pressure in the cuff is too high (over

299 mmHg) OR the pulse is too high

(over 200 beats per minute). Relax for 5

minutes and repeat the measurement.*

Pulse too

low

The pulse is too low (less than 40 beats

per minute). Repeat the measurement.*

Error

Description

Potential cause and remedy

1. Remove the cuff connector 9 from the cuff tube AT and care-

fully pull the bladder through the opening at the edge of the cuff

cover.

2. Hand wash the cuff cover in soapsuds: not hotter than 30 °C.

3. Completely dry the cuff cover by linen drying.

4. Loop the cuff tube back through its opening and carefully place

the bladder flat in the cuff cover.

5. Reattach the cuff connector on the cuff tube.

The bladder must lay straight in the cuff cover, not folded.

Do not use fabric softener.

WARNING: Do not wash the cuff in a washing machine or

dishwasher!

WARNING: Do not dry the cuff cover in a tumble dryer!

WARNING: Under no circumstances may you wash the

inner bladder!

Accuracy test

We recommend this device is tested for accuracy every 2 years or

after mechanical impact (e.g. being dropped). Please contact your

local Microlife-Service to arrange the test (see foreword).

Disposal

Batteries and electronic devices must be disposed of in

accordance with the locally applicable regulations, not with

domestic waste.

9. Guarantee

This device is covered by a 5 year guarantee from the date of

purchase. During this guarantee period, at our discretion, Microlife

will repair or replace the defective product free of charge.

Opening or altering the device invalidates the guarantee.

The following items are excluded from the guarantee:

Transport costs and risks of transport.

Damage caused by incorrect application or non-compliance

with the instructions for use.

Damage caused by leaking batteries.

Damage caused by accident or misuse.

Packaging/storage material and instructions for use.

Regular checks and maintenance (calibration).

Accessories and wearing parts: Batteries, power adapter

(optional).

The cuff is covered by a functional guarantee (bladder tightness)

for 2 years.

Should guarantee service be required, please contact the dealer

from where the product was purchased, or your local Microlife

service. You may contact your local Microlife service through our

website:

www.microlife.com/support

Compensation is limited to the value of the product. The guarantee

will be granted if the complete product is returned with the original

invoice. Repair or replacement within guarantee does not prolong

or renew the guarantee period. The legal claims and rights of

consumers are not limited by this guarantee.

10.Technical Specifications

This device complies with the requirements of the Medical Device

Directive 93/42/EEC.

Technical alterations reserved.

Operating condi-

tions:

10 - 40 °C / 50 - 104 °F

15 - 95 % relative maximum humidity

Storage conditions: -20 - +55 °C / -4 - +131 °F

15 - 95 % relative maximum humidity

Weight: 277 g (including batteries)

Dimensions: 131 x 90 x 60.5 mm

Measuring proce-

dure:

oscillometric, corresponding to Korotkoff

method: Phase I systolic, Phase V

diastolic

Measurement range: 20 - 280 mmHg – blood pressure

40 - 200 beats per minute – pulse

Cuff pressure display

range: 0 - 299 mmHg

Resolution: 1 mmHg

Static accuracy: pressure within ± 3 mmHg

Pulse accuracy: ± 5 % of the readout value

Voltage source: 4 x 1.5 V alkaline batteries; size AA

Mains adapter DC 6V, 600 mA (optional)

Battery lifetime: approx. 920 measurements

(using new batteries)

IP Class: IP20

Reference to

standards:

EN 1060-1 /-3 /-4; IEC 60601-1;

IEC 60601-1-2 (EMC); IEC 60601-1-11

Expected service life: Device: 5 years or 10000 measurements

Accessories: 2 years

7BP B2 Basic ES

Pantalla

Lea atentamente las instrucciones antes de utilizar este

dispositivo.

Pieza aplicada tipo BF

Uso previsto:

Este monitor de presión arterial oscilométrico está diseñado para

medir la presión arterial no invasiva en personas de 12 años o más.

Está clínicamente validado en pacientes con hipertensión, hipo-

tensión, diabetes, embarazo, preeclampsia, aterosclerosis, enfer-

medad renal en etapa terminal, obesidad y adultos mayores.

Estimado cliente,

Este dispositivo ha sido desarrollado en colaboración con médicos

y su muy alta precisión ha sido probada en ensayos clínicos.*

Si tiene cualquier pregunta o problema o si desea pedir piezas de

recambio, no dude en contactar con su servicio de atención al

cliente de Microlife local. Su distribuidor o farmacia podrá indicarle

la dirección del distribuidor de Microlife en su país. También puede

visitarnos en Internet en www.microlife.com donde encontrará

información útil sobre nuestros productos.

¡Cuide su salud con Microlife AG!

* Este dispositivo usa la misma tecnología de medición que el

premiado modelo «BP 3BTO-A» probado de acuerdo con el proto-

colo de la Sociedad Británica e Irlandesa de Hipertensión (BIHS).

Índice

1. Uso del dispositivo por primera vez

• Colocar las baterías

• Ajuste de fecha y hora

• Elegir el manguito correcto

2. Lista de verificación para tomar una medida confiable

3. Medición de la presión arterial

• Inflación manual

• Procedimiento para no guardar la lectura

• ¿Cómo he de evaluar mi presión arterial?

• Apariencia del símbolo de latidos irregulares (IHB)

4. Memoria de datos

• Ver los valores guardados

• Borrar todos los valores

5. Indicador de baterías y cambio de baterías

• Baterías con poca carga

• Baterías descargadas – cambio

Microlife BP B2 Basic ES

1Botón ON/OFF (Encendido/Apagado)

2Pantalla

3Botón M (Memoria)

4Botón Hora

5Enchufe para manguito

6Enchufe para adaptador de corriente

7Compartimento de baterías

8Brazalete

9Conector del manguito

AT Tubo de brazalete

AK Valor sistólico

AL Valor diastólico

AM Frecuencia del pulso

AN Indicador de batería

AO Indicador de semáforo

AP Valor guardado

AQ Indicador del pulso

AR Control de ajuste del brazalete

-A: Ajuste subóptimo del brazalete

-B: Indicador de movimiento del brazo «Err 2»

-C: Comprobación de la presión del brazalete «Err 3»

AS Indicador de señal del brazalete «Err 1»

BT Símbolo de latidos irregulares (IHB)

BK Fecha/Hora

Mantener en lugar seco

• ¿Qué baterías y qué procedimiento?

• Uso de baterías recargables

6. Uso de un adaptador de corriente

7. Mensajes de error

8. Seguridad, cuidado, control de precisión y eliminación de

residuos

• Seguridad y protección

• Cuidado del dispositivo

• Limpieza del brazalete

• Control de precisión

• Eliminación de residuos

9. Garantía

10. Especificaciones técnicas

Tarjeta de garantía (véase reverso)

1. Uso del dispositivo por primera vez

Colocar las baterías

Después de desembalar el dispositivo, en primer lugar, inserte las

baterías. El compartimento de las baterías 7 está en la parte infe-

rior del dispositivo. Inserte las baterías (4 x 1,5 V, tamaño AA) de

acuerdo con las marcas de polaridad indicadas.

Ajuste de fecha y hora

1. Una vez activadas las baterías, el número del año parpadea en

la pantalla. Ajuste el año pulsando el botón M 3. Para confir-

marlo y ajustar a continuación el mes, pulse el botón Hora 4.

2. Ahora puede ajustar el mes usando el botón M. Pulse el botón

Hora para confirmar y, a continuación, ajuste el día.

3. Por favor, siga las instrucciones anteriores para ajustar el día,

la hora y los minutos.

4. Una vez que haya ajustado los minutos y pulsado el botón Hora,

la fecha y la hora quedan establecidas y se visualiza la hora.

5. Si desea cambiar la fecha y la hora, pulse y mantenga pulsado

el botón Hora durante aprox. 3 segundos hasta que comience

a parpadear el número del año. Ahora, podrá introducir los

nuevos valores tal como se ha descrito anteriormente.

Elegir el manguito correcto

Microlife ofrece diferentes tamaños de manguitos. Elija el tamaño

de manguito adecuado según la circunferencia de su brazo

(medida de forma ajustada en el centro del brazo).

Como opción existen manguitos preformados.

Use únicamente manguitos Microlife.



Contacte su servicio al cliente de Microlife local, si el manguito

8 incluido no es el adecuado para usted.



Conecte el manguito al dispositivo insertando el conector 9

del manguito en el enchufe 5 del manguito hasta que no entre

más.

2. Lista de verificación para tomar una medida

confiable



Evite comer o fumar, así como cualquier otra actividad inmedia-

tamente antes de la medición.



Siéntese en una silla con respaldo y relájese durante 5 minutos.

Mantenga los pies planos sobre el piso y no cruce las piernas.



Efectúe la medición siempre en el mismo brazo (normal-

mente en el izquierdo). Es recomendable que su médico realice

dos mediciones en cada brazo durante la primera visita para

determinar de qué brazo se tomarán las mediciones en el

futuro. Las mediciones se deben efectuar en el brazo con

presión arterial más alta.



Quítese las prendas de vestir ajustadas a su brazo. Para evitar

la constricción, no se deben arremangar las mangas de

camisa, ya que no interfieren con el manguito si se encuentran

en contacto con el brazo.



Asegúrese de utilizar el tamaño correcto del manguito

(marcado en el manguito).

Coloque el manguito de tal forma que esté ajustado, pero

que no quede demasiado apretado.

Asegúrese de que el manguito esté colocado 1-2 cm por

encima del codo.

La marca de la arteria en el manguito (barra larga de 3 cm)

debe descansar sobre la arteria que va en el lado interior del

brazo.

Coloque el brazo de tal forma que esté relajado.

Asegúrese de que el manguito se encuentre a la misma

altura que su corazón.

Tamaño de manguito para una circunferencia del brazo

S 17 - 22 cm

M 22 - 32 cm

M - L 22 - 42 cm

L 32 - 42 cm

L - XL 32 - 52 cm

Il n'est pas non plus inhabituel de constater des écarts entre les

mesures prises par le médecin ou à la pharmacie et celles que

vous effectuez à la maison puisque les environnements sont

très différents.

L’affichage du pouls ne permet pas de contrôler la

fréquence des stimulateurs cardiaques.

Si vous êtes enceinte, vous devriez surveiller régulièrement

votre tension artérielle car elle peut changer drastiquement

durant cette période.

Ne laissez jamais les enfants utiliser l'appareil sans surveil-

lance. Certaines de ses parties sont si petites qu'elles

peuvent être avalées. Possible risque d’étranglement dans le

cas où l’appareil est fourni avec des câbles ou des tuyaux.

Entretien de l'appareil

Utilisez exclusivement un chiffon sec et doux pour nettoyer l'appareil.

Nettoyage du brassard

Le brassard fourni avec cet appareil est lavable.

1. Retirez le connecteur du brassard 9 du tuyau AT et retirez

doucement la poche gonflable au travers de l'ouverture située

sur le bord de la housse.

2. Lavez à la main la housse du brassard dans de l'eau savon-

neuse: pas plus de 30 °C.

3. Séchez complètement la housse en l'étendant.

4. Réinserez la poche gonflable dans la housse et placez-la

soigneusement à plat à l'intérieur.

5. Remettez le connecteur dans le tube du brassard.



La poche gonflable doit être à plat et non pliée dans la housse.

N'utilisez pas d'adoucissant.

AVERTISSEMENT: Ne pas laver le brassard en machine

ou au lave vaisselle!

AVERTISSEMENT: Ne séchez pas la housse du brassard

dans un sèche-linge!

ATTENTION: Ne lavez jamais la poche intérieure du bras-

sard!

Test de précision

Nous recommandons de faire contrôler la précision de cet appareil

tous les 2 ans ou après un choc mécanique (par ex. chute).

Veuillez-vous adresser à votre Service Microlife local pour

convenir d'une date (voir avant-propos).

Élimination de l'équipement

Les piles et appareils électroniques doivent être éliminés en

conformité avec les prescriptions locales, séparément des

ordures ménagères.

9. Garantie

Cet appareil est couvert par une garantie de 5 ans à compter de

la date d'achat. Pendant cette période de garantie, à notre discré-

tion, Microlife réparera ou remplacera sans frais le produit défec-

tueux.

Le fait d'ouvrir ou de modifier l'appareil invalide la garantie.

Sont exclus de la garantie, les cas suivants:

Frais de transport et risques de transport.

Dommages causés par une utilisation incorrecte ou le non-

respect du mode d'emploi.

Dommages causés par une fuite des piles.

Dommages causés par un accident ou une mauvaise utilisa-

tion.

Matériel d'emballage / stockage et mode d'emploi.

Contrôles et maintenance réguliers (étalonnage).

Accessoires et pièces d'usure: Piles, adaptateur secteur (en

option).

Le brassard est couvert par une garantie de fonctionnement de 2

ans.

Pour toute demande de garantie, veuillez contacter le revendeur

auprès duquel le produit a été acheté ou le bureau local Microlife.

Vous pouvez également nous joindre via notre site Internet:

www.microlife.com/support

L'indemnisation est limitée à la valeur du produit. La garantie peut

être accordée que si le produit est retourné complet avec la facture

d'origine. La réparation ou le remplacement sous garantie ne

prolonge ni ne renouvelle la période de garantie. Les prétentions

légales et droits des consommateurs ne sont pas limités par cette

garantie.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Microlife BP B2 BASIC in the language / languages: English, German, Dutch, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 1.36 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Microlife BP B2 BASIC Manual

Product: