Manual Microlife BP A90-30 (page 6 of 37) (English, German, Turkish)

536798

Zoom out

Zoom in

1/37

5. Data Memory

At the end of each measurement, this instrument automatically

stores the result.

Viewing the stored values

Press the M-button AO briefly, when the instrument is switched off.

The display first shows the last stored result.

Pressing the M-button again displays the previous value. Pressing

the M-button repeatedly enables you to move from one stored

value to another.

Memory full

When the memory has stored 30 results, the memory is full.

From this point onwards, a new measured value is stored

by overwriting the oldest value.

Clearing all values

All memory data are cleared when batteries are taken out

of the instrument.

6. Battery Indicator and Battery change

Low battery

When the batteries are approximately ¾ empty the battery symbol

AK will flash as soon as the instrument is switched on (partly filled

battery displayed). Although the instrument will continue to

measure reliably, you should obtain replacement batteries.

Flat battery – replacement

When the batteries are flat, the battery symbol

will flash as soon

as the instrument is switched on (flat battery displayed). You cannot

take any further measurements and must replace the batteries.

1. Open the battery compartment 4 at the back of the instrument.

2. Replace the batteries – ensure correct polarity as shown by the

symbols in the compartment.

Which batteries and which procedure?



Use 4 new, long-life 1.5V, size AA batteries.



Do not use batteries beyond their date of expiry.



Remove batteries if the instrument is not going to be used

for a prolonged period.

Using rechargeable batteries

You can also operate this instrument using rechargeable batteries.



Only use «NiMH» type reusable batteries.



Batteries must be removed and recharged when the flat

battery symbol appears. They should not remain inside the

instrument as they may become damaged (total discharge as

a result of low use of the instrument, even when switched off).



Always remove the rechargeable batteries if you do not

intend to use the instrument for a week or more.



Batteries cannot be charged in the blood pressure monitor.

Recharge batteries in an external charger and observe the

information regarding charging, care and durability.

7. Error Messages

If an error occurs during the measurement, the measurement is

interrupted and an error message, e.g. «ERR 3», is displayed.

* Please consult your doctor, if this or any other problem occurs

repeatedly.



If you think the results are unusual, please read through the

information in «Section 1.» carefully.

Error

Description

Potential cause and remedy

ERR 1

» Signal too

weak

The pulse signals on the cuff are too weak.

Re-position the cuff and repeat the

measurement.*

ERR 2

» Error signal During the measurement, error signals were

detected by the cuff, caused for instance by

movement or muscle tension. Repeat the

measurement, keeping your arm still.

ERR 3

» No pressure

in the cuff

An adequate pressure cannot be generated

in the cuff. A leak may have occurred.

Check that the cuff is correctly connected

and is not too loose. Replace the batteries if

necessary. Repeat the measurement.

ERR 5

» Abnormal

result

The measuring signals are inaccurate and

no result can therefore be displayed. Read

through the checklist for performing reliable

measurements and then repeat the

measurement.*

» Pulse or

cuff pres-

sure too

high

The pressure in the cuff is too high (over

300 mmHg) OR the pulse is too high (over

200 beats per minute). Relax for 5 minutes

and repeat the measurement.*

» Pulse too

low

The pulse is too low (less than 40 beats per

minute). Repeat the measurement.*

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Microlife BP A90-30 in the language / languages: English, German, Turkish as an attachment in your email.

The manual is 1,55 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Microlife BP A90-30 Manual

Product: