517345

Metz Mecablitz 52 AF-1 Nikon digital Manual

182
Zoom out
Zoom in
Previous page
1/286
Next page
182
k
16 Troubleshooting
Should the flash unit fail to function properly or meaningless con-
tent appear on the flash unit display panel, switch the flash unit off
with the main switch ባ for approximately 10 seconds. Check the
camera settings and make sure the foot of the flash unit is mounted
correctly in the camera’s accessory shoe.
Replace the batteries with new or freshly charged batteries.
The flash unit should function normally again once it is switched
back on. If this is not the case, contact your local dealer.
Below is a list of some of the problems that may occur when the
flash unit is used. For each item, possible causes and remedies for
the problem are listed.
No maximum flash range indication appears on the display panel.
• There has been no exchange of data between the flash unit and
the camera. Tap the camera’s shutter release.
• The reflector is not in normal position.
The AF measuring beam of the flash unit is not activated.
• The flash unit is not ready for firing.
• The camera is not in „Single-AF (S-AF)“ mode.
• The camera supports only its own internal AF measuring beam.
• Some cameras support the AF measuring beam in the flash unit
only with the camera’s central AF sensor. If a peripheral AF sensor
is selected, then the AF measuring beam will not be activated in
the flash unit!
Activate the central AF sensor.
• The "AF BEAM" is switched off. Switch on "AF BEAM", see 11.3.
The reflector position is not automatically adjusted to the current
zoom position of the lens.
• The camera does not transfer data to the flash unit
• There is no exchange of data between the flash unit and the
camera. Tap the camera’s shutter release.
• The camera is equipped with a lens without CPU.
• The flash unit operates in manual zoom mode „MZoom“.
Switch to Auto-Zoom (see 11.2.3).
• The reflector is swivelled out of its locked normal position.
• The wide-angle diffuser folds out from the reflector.
• A Mecabounce is mounted in front of the reflector.
The aperture setting on the flash unit is not automatically adjusted
to that of the lens.
• The camera does not transfer data to the flash unit
• There is no exchange of data between the flash unit and the
camera. Tap the camera’s shutter release.
• The camera is equipped with a lens without CPU.
The i flash mode cannot be set.
• Data transfer has not occurred between the flash unit and the
camera.Actuate shutter release.
• The camera does not support i TTL flash mode.
The setting for manual TTL flash exposure correction has no effect.
• The camera does not support manual TTL flash exposure
correction on the flash unit.
… 182 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metz Mecablitz 52 AF-1 Nikon digital at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metz Mecablitz 52 AF-1 Nikon digital in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 3,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info