517343
21
Zoom out
Zoom in
Previous page
1/55
Next page
7.1 Der drahtlose Metz TTL-Remote-Betrieb
Bild 14: Einstellvorgang für den Metz TTL-Remote-Betrieb
Einstellvorgang für den Metz TTL-Remote-Betrieb:
Kamera gemäß den Angaben ihrer Bedienungsanleitung einstellen.
Kamerasynchronzeit auf 1/60 Sek. oder länger einstellen.
Controller an der Kamera mit dem Hauptschalter (16) einschalten.
1 Betriebsartenschalter (28) auf TTL schieben.
2 Am Steuergerät auf der Kamera die Taste Remote (22) drücken. Die Entfernungswerte im
LC-Display erlöschen.
3 mit der - bzw.+ Taste (24) die Controller-Adresse Co 1 oder Co 2 wählen.
Slave-Blitzgeräte 40 MZ-. . mit einem Slave Adapter SCA 3080 ausrüsten, mit dem Haupt-
schalter einschalten und auf TTL stellen. Die Slave-Blitzgeräte 40 MZ-. . sind jetzt in den Sla-
ve-Betrieb geschaltet. Die Slave-Blitzgeräte 50 MZ-5 (ohne Steuergerät) mit dem Haupt-
schalter einschalten. Die Zoomeinstellung des Hauptreflektors kann mit dem Schalter
(21) in 4 Stufen eingestellt werden: Stellung 0 = 28 mm, 1/4 = 35 mm, 1/2 = 50 mm und 1
= 85 mm. Blitzbereitschaft aller Geräte abwarten.
4 Am Steuergerät auf der Kamera die Handauslösetaste (35) drücken und einen Probeblitz
auslösen, damit der Slave auf die Controller-Adresse eingestellt wird.
Das Slave-Blitzgerät antwortet mit einem zeitverzögerten Blitz und zeigt damit an, daß es
betriebsbereit ist. Werden mehrere Slaves gleichzeitig betrieben, so erfolgt die Quittierung aller
Slaves zeitgleich. Gibt ein Slave-Blitzgerät keinen zeitverzögerten Blitz ab, so hat der Sensor (13)
im Stab des Slave-Blitzgerätes keinen Lichtimpuls empfangen. Drehen Sie dann den Stab des
Blitzgerätes so, daß der Sensor (13) den Lichtimpuls des Controllers auf der Kamera empfangen
kann, und wiederholen Sie Arbeitsgang Nr. 4. Bei besonders kurzem Abstand zwischen Controller
und Slave kann u. U. der Fotosensor (4) des Controllers die Lichtabstrahlung unterbrechen,bevor
der Slave seine Information erhalten hat. Vergrößern Sie dann den Abstand zwischen Controller
und Slave oder wählen eine größere Blendenzahl und lösen nochmals einen Probeblitz aus.
21
1
2
4
3
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metz MECABLITZ 50 MZ-5 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metz MECABLITZ 50 MZ-5 in the language / languages: German as an attachment in your email.

The manual is 1,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info