517341
89
Zoom out
Zoom in
Previous page
1/182
Next page
ķ
If your flash unit is not going to be used for an extended period of time,
remove the batteries.
Replacing batteries
The batteries are flat or dead if the recycling time (elapsing from the triggering
of a full-power flash, e.g. in the M mode, to the moment the flash ready indica-
tor
lights up again) exceeds 60 seconds.
• Turn off the flash unit at the main switch
.
• Slide the battery compartment cover
forwards
and fold open.
• Insert the batteries lengthwise as indicated by the
battery symbols provided. First, insert the batteries
that face the display and then the others.
Close the battery cover
.
When inserting batteries, ensure that the polari-
ty is correct and matches the symbols in the bat-
tery compartment. Inserting the batteries in the
wrong direction can destroy the flash unit!
Always replace all batteries simultaneously, and
make sure that batteries are the same brand
and have the same capacity.
Flat or dead batteries should not be disposed
of with ordinary household waste. Help protect
the environment, and dispose of flat/dead bat-
teries at the appropriate collection points.
3.3 Switching the flash unit on and off
The flash unit can be turned on by flipping the main
switch
to the „ON“ position.
To turn off the flash unit, flip the main switch
to the
left position.
If your flash unit is not going to be used for an
extended period of time, we recommend turning it off with the main
switch and removing the power source (i.e., batteries).
3.4 Auto OFF for the flash unit
To save battery power and prevent inadvertent battery drain, the flash unit is
factory-set to automatically switch to standby mode (Auto OFF) 10 minutes after
• being switched on,
• after pressing a key,
• a flash is fired
• the shutter release is actuated
• the camera’s exposure metering system is switched off.
...in stand-by mode, (Auto-OFF) is activated to save energy and to protect the
power source from unintentional discharging. The active automatic cut-off is
shown in the display . The flash ready indicator and the indicators on
the LC display disappear.
In slave mode, the automatic cut-off is not activated.
The most recently used operating setting is retained after automatic shutdown and
is immediately restored when the camera is switched on. The flash unit can be tur-
ned on again by pressing any button, or by tapping on the shutter release
(wake-up function).
The flash unit should always be turned off using the main switch
if it
is not going to be used for an extended period.
If necessary, the Auto OFF function can be set to occur after 1 minute of inacti-
vity, or can be deactivated (see 9.4).
89
709 47 0191.A3 50AF-1 Pen. 17.12.2010 13:22 Uhr Seite 89
89


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metz MECABLITZ 50 AF-1 digital Pentax at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metz MECABLITZ 50 AF-1 digital Pentax in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 4,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info