517338
94
Zoom out
Zoom in
Previous page
1/174
Next page
94
ķ
Setting procedure for remote slave flash mode
• Press the button combination „Select“ until
“ flashes in the display.
• Apply the setting desired with the buttons
+ and —.
– When „On“ is displayed, the remote sla-
ve mode is activated.
– When „OFF“ is displayed, the remote
slave mode is deactivated.
The setting takes effect immediately. After about 5 seconds the display stops
flashing and the setting is saved automatically. After activation of the remote
slave mode, „ “ appears in the display. In addition, the slave group (GROUP)
selected and the remote channel (CH) are shown.
Setting of the slave group
• With the remote slave mode activated,
press the button combination „Select“ until
„GROUP“ (= slave group) flashes in the
display.
• Apply the setting desired with the buttons
+ and —. Selection of group A, B or C is
possible.
The setting takes effect immediately. After about 5 seconds the display stops
flashing and the setting is saved
automatically. After activation of the remote slave mode, „ “ appears in the
display. In addition, the slave group (GROUP) selected and the remote channel
(CH) are shown.
SL
SL
SL
Setting of the remote channel
The same remote channel must be set on the slave flash unit as on the
master or controller flash unit!
• With the remote slave mode activated,
press the button combination „Select“ until
„CH“ (= remote channel) flashes in the
display.
• Apply the setting desired with the buttons + and —.
Selection of group 1, 2, 3 or 4 is possible.
The setting takes effect immediately.
After about 5 seconds the display stops flashing and the setting is saved auto-
matically. After activation of the remote slave mode, „ “ appears in the
display. In addition, the slave group (GROUP) selected and the remote channel
(CH) are shown.
Testing remote flash mode
• Place the slave flash units in the desired positions for the shot. Use flash unit
mounting foot S60 (optional accessories, see 17) to set up the slave flash unit.
• Wait for all of the flash units involved to become flash ready. Once the slave
flash units are flash ready, the AF measuring beam will blink.
• Press the manual firing button on the master or controller flash unit to fire a
test flash. The slave flash units will respond in succession, according to slave
group, with a test flash. If a slave unit fails to fire a test flash, check the set-
tings for remote channel and slave group. Correct the position of the slave
flash unit so that it is able to receive light from the master flash unit via the
sensor .
The flash mode is transmitted automatically by master or controller.
When the flash unit functions as master in the cordless remote system,
the activation of the modelling light also activates the modelling light of
slave flash units
SL
On
SL
SL
GROUP B
GROUP B
CH
2
CH
2
709 47 0175.A2 50 AF-1 C 26.08.2010 15:53 Uhr Seite 94
94


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metz MECABLITZ 50 AF-1 digital Canon at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metz MECABLITZ 50 AF-1 digital Canon in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 4,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info