517330
52
Zoom out
Zoom in
Previous page
1/104
Next page
ķ
52
3 Preparing the flash unit for use
Attaching the flash unit to the camera
The flash unit can be attached to the camera and operated with:
- a synch cable 45-47
2)
.
- a standard foot 301
1)
and a synch cable SCA 300A
1)
- an SCA 3xx adapter
1)
and a synch cable SCA 300A
1)
- an SCA 3xx2 adapter
1)
and a synch cable SCA 3045
3)
.
Be sure to switch off the flash unit by its main switch prior to mounting
or removing the connecting components! Before mounting or removing
the flash unit, switch off both the camera and the flash unit!
Mounting the flash unit:
• Push the SCA adapter or standard foot 301 into the camera’s accessory
shoe and lock in place with the knurled nut.
• Fasten the camera bracket with the bracket screw to the camera’s tripod
socket. For medium- and large-format cameras we recommend the use of
the 70-35 bracket (optional extra).
• Insert the camera bracket into the mount of the bracket holder until it
is audibly engaged.
• Secure the camera bracket with the locking screw.
• Connect the synch or connecting cable to the flash unit and camera or
adapter.
4 Power supply
The flash unit can be operated with:
• 6 alkaline manganese batteries IEC LR 6 (AA-type) in the battery holder
45-39
2)
(optional extra), or
• Metz NiMh battery pack 45-56
3)
, or
• Power Pack P76 (optional extra)
Do not use lithium cells! Their higher voltage would damage the flash
unit’s electronic system. Only use the permitted power sources (see
above). Warranty claims for faults and damage to the flash unit arenot
accepted if they were caused by the use of accessories from other
manufacturers.
Battery replacement
Press the two locking keys of the battery holder
2)
and pull the holder out of
the flash unit (Fig 4a). To return the battery holder insert it into the flash unit’s
handle-mount grip and press it until it audibly locks in place.
Exchanging the batteries
Press together the two smooth locking keys of the dismantled battery holder
(optional extra) and remove the lid (Fig. 4b). Insert new batteries in confor-
mity with the polarity symbols indicated on the bottom of the holder. Return
the lid and lock in again.
Mixed up battery poles may destroy the flash unit.. Replace all batte-
ries at a time and make sure that the batteries are of the same brand
and type and have the same capacity! Spent batteries must not be
thrown into the domestic waste! Help keep the environment clean and
discard spent batteries at corresponding collecting points.
New NiMH batteries and those that have not been in use for a long
period of time can be almost completely flat. If this is the case, the
charger does not always recognise the NiMH battery state of charge.
This results in the NiMH battery only being partially charged. If the
partially charged battery is then inserted in the flash unit, the battery
indicator signalises a discharged battery or the flash unit does not
reach flash readiness.
In this case the NiMH battery must be recharged several times in suc-
cession (approx. 2-5 charging operations).
The battery must be removed from the charger briefly between char-
ging operations.
708 47 0026-A1 BASIC-KIT 14.10.2008 12:54 Uhr Seite 52
52


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metz Mecablitz 45 CL-4 digital BASIC-KIT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metz Mecablitz 45 CL-4 digital BASIC-KIT in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info