517326
31
Zoom out
Zoom in
Previous page
1/60
Next page
31
ķ
• Connect the synch cable to the flashgun and camera.
2.2 Power supply
The flashgun can be operated with:
• Alkaline manganese batteries, size IEC LR 6 (AA-type) (only with BAT-ver-
sion, otherwise optional extra)
• Metz NiCad battery pack 45-40 (only if NiCad is featured; otherwise
available as an optional accessory). A charger (see table 2, page 59) is
included with the flashgun if NiCad is featured).
• Power Pack P 50 (optional accessory)
2.3 Battery replacement
Press the two locking keys of the battery housing, and pull out of the flashgun
(fig. 4a). To return the battery housing press the two locking keys together
and press into the handle-mount grip of the flashgun until it audibly engages.
2.3.1 Exchanging the batteries
Press together the smooth locking keys of the dismantled battery housing
(only with BAT-version, otherwise optional extra) and remove the lid (fig. 4b).
Insert new batteries in conformity with the polarity symbols indicated in the
base of the housing. Return the lid and lock in again.
Spent batteries must not be thrown into the domestic waste! Help keep
the environment clean and discard spent batteries at corresponding
collecting points!
The battery housing must not be fitted with NiCad batteries! The contacts of
the battery housing are only intended for alkaline manganese batteries.
The lower resistance of NiCad batteries means that more current can
flow, and this can damage the flashgun. The NiCad Battery Pack 45-
40 has special contacts which do not allow the flow of high currents.
2.3.2 Operation with the battery pack
(only with NC-version, otherwise optional extra)
The NiCad battery should be charged for 5 hours before it is used for the
first time. The NiCad battery can be charged within the flashgun or external-
ly.
Warning: The flashgun must NOT be switched on while the battery is
being charged within the flashgun!
The NiCad battery is discharged if the recycle time after a flash exceeds 60
seconds.
Adjust the correct mains voltage on the charger prior to charging. The volta-
ge selector (fig. 5a) is located next to the plug and can be adjusted with a
small screwdriver.
The connection for the charger (fig. 5b) is in the base of the NiCad battery.
The adjoining pilot lamp lights up while charging is in progress.
The charging time for a completely exhausted NiCad battery is 5 hours. A
partly discharged NiCad battery requires a correspondingly diminished
charging time.
T
o identify an exhausted batter
y: Push the knurled slide in the battery lid to
the black mark.
T
o identify a charged batter
y: Push the knurled slide in the battery lid to the
white mark.
2.4 Switching the flashgun on and off
The flashgun is switched on with the main switch (fig. 2). The flashgun is
permanently switched on when the switch is pushed to the top position, and
the operating light shines. Push the main switch to the bottom position to
switch off the flashgun.
703 47 0130.A1 45 CL-1 NC 13.11.2006 14:33 Uhr Seite 31
31


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metz MECABLITZ 45 CL-1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metz MECABLITZ 45 CL-1 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info