517286
5
Zoom out
Zoom in
Previous page
1/176
Next page
• Blitzgerät nicht zerlegen! HOCHSPANNUNG!
Reparaturen sollten ausschließlich von einem
autorisierten Service ausgeführt werden.
Elektrische Kontakte des Blitzgerätes nicht berühren.
• Wurde das Gehäuse so stark beschädigt, dass
Innenteile frei liegen, darf das Blitzgerät nicht
mehr betrieben werden. Batterien entnehmen!
Keine schadhaften Batterien oder Akkus verwenden!
2. Vorbereiten
2.1 Stromversorgung
Das Blitzgerät kann wahlweise betrieben werden mit:
• 2 Alkali-Mangan-Trockenbatterien Typ IEC LR03
(AAA / Micro), wartungsfreie Stromquelle für
gemäßigte Leistungsanforderungen.
• 2 Nickel-Metall-Hydrid Akkus Typ IEC HR03
(AAA / Micro), deutlich höhere Kapazität als
NC-Akkus und weniger umweltschädlich als
NC-Akkus da cadmiumfrei. Sie bieten sehr kur-
ze Blitzfolgezeiten und sparsamen Betrieb, da
sie wiederaufladbar sind.
• 2 NC-Akkus Typ IEC KR03 (AAA / Micro).
Die Batterien / Akkus sind leer bzw. ver-
braucht, wenn die Blitzfolgezeit bei Blitzen
mit voller Lichtleistung über 60 Sek. ansteigt.
Wenn Sie das Blitzgerät längere Zeit nicht
benutzen, entfernen Sie bitte die Batterien
aus dem Gerät.
2.2 Einlegen und Auswechseln
der Batterien
• Schalten Sie das Blitzgerät mit dem Hauptschal-
ter aus.
• Batteriefachdeckel zur Außenseite des Blitzgerä-
tes verschieben.
• Batterien entsprechend den Symbolen auf der
Innenseite des Batteriefachdeckels einlegen.
Achten Sie beim Einsetzen der Batterien dar-
auf, dass + Pol und – Pol wie auf den Sym-
bolen angezeigt liegen. Vertauschte Pole
können zur Zerstörung des Gerätes führen!
Ersetzen Sie immer beide Batterien durch
gleiche Batterien des selben Herstellertyps
mit gleicher Kapazität!
5
j
703 47 0165-A3 28 CS-2 digi 13.03.2006 11:55 Uhr Seite 5
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metz MECABLITZ 28 CS-2 digital at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metz MECABLITZ 28 CS-2 digital in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info