Manual Metabo WP 11-125 QuickProtect (page 16 of 108) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

665549

Zoom out

Zoom in

1/108

ENGLISHen

downwards so that the clamping nut can be

attached securely to the spindle.

Z) Only with W 8-100:

The collar of the adjusting nut faces downwards

and/or the flat surface faces upwards.

- Lock the spindle. Turn the clamping nut (12)

clockwise using the 2-hole spanner (13) to secure.

Releasing the clamping nut:

- Lock the spindle (see chapter 7.1). Turn the

clamping nut (12) anticlockwise using the 2-hole

spanner (13) to unscrew.

8.1 Adjusting the speed

(depending on features)

Set the recommended speed at the setting

wheel (7).

Parting grinder and roughing discs, cup wheel,

diamond parting wheel: high speed

Brush: medium speed

Grinding wheel: low to medium speed

Note:

We recommend using our angle polisher for

polishing work.

8.2 Switching On and Off

Always guide the machine with both hands.

Switch on first, then guide the

accessory

towards the workpiece.

The machine must not be allowed to draw in

additional dust and shavings. When switching

the machine on and off, keep it away from dust

deposits. After switching off the machine, only place

it down when the motor has come to a standstill.

Avoid inadvertent starts: always switch the

tool off when the plug is removed from the

mains socket or if there has been a power cut.

In continuous operation, the machine

continues running if it is forced out of your

hands. Therefore, always hold the machine with

both hands using the handles provided, stand in a

safe position and concentrate.

Machines with slide switch:

Switching on: Push the slide switch (5) forward.

For continuous activation, now tilt

downwards until it engages.

Switching off: Press the rear end of the slide

switch (5) and release.

Machines with "Ergo Paddle Switch" (with

dead man function):

(machines with the designation WP..., WEP...)

Switching on: Slide the switch-on lock (8) in

the direction of the arrow and press

the trigger (9).

Switching off: Release the trigger (9).

8.3 Working instructions

Grinding and sanding operations:

Press down the machine evenly on the surface

and move back and forth so that the surface of the

workpiece does not become too hot.

Roughing: position the machine at an angle of 30° -

40° for the best working results.

Separating:

Always work against the run of the disc

(see illustration). Otherwise there is

the danger of the machine kicking

back from the cut out of control. Guide

the machine evenly at a speed

suitable for the material being processed. Do not tilt,

apply excessive force or sway from side to side.

Wire brushing:

Press down the machine evenly.

Motor cleaning: blow compressed air through the

rear ventilation slots of the machine regularly,

frequently and thoroughly. Here, the machine must

be held firmly.

Machines with VTC and TC electronics:

The electronic signal display (6) lights up and

the load speed decreases.

The coil temperature is

too high! Run the machine in idling until the

electronics signal indicator switches off.

Machines with VTC, TC and VC electronics:

The electronic signal display (6) flashes

and the machine does not start. The restart

protection is active. If the mains plug is

inserted with the machine switched on, or if the

current supply is restored following an interruption,

the machine does not start up. Switch the machine

off and on again.

Use only genuine Metabo accessories. See page 4.

Use only accessories which fulfil the requirements

and specifications listed in these operating instruc-

tions.

8. Use

9. Cleaning

10. Troubleshooting

11. Accessories

8 989

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Metabo WP 11-125 QuickProtect in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,65 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Metabo WP 11-125 QuickProtect Manual

Product: