Manual Metabo WEVA 15-150 Quick (page 17 of 124) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

595536

Zoom out

Zoom in

1/124

ENGLISH en

occupational health and safety regulations,

disposal).

Collect the generated particles at the source, avoid

deposits in the surrounding area.

Use suitable accessories for special work (see

chapter 11.), thus less particles enter the

environment in an uncontrolled manner.

Use a suitable extraction unit.

Reduce dust exposure with the following measures:

- Do not direct the escaping particles and the

exhaust air stream at yourself or nearby persons

or on dust deposits.

- Use an extraction unit and/or air purifiers

- Ensure good ventilation of the workplace and

keep clean using a vacuum cleaner Sweeping or

blowing stirs up dust

- Vacuum or wash the protective clothing Do not

blow, beat or brush

See page 2.

1 "Quick"clamping nut *

2Spindle

3 Autobalancer support flange *

4 Spindle locking button

5 Sliding on/off switch *

6Handle

7 Electronic signal indicator *

8 Thumbwheel for selection of speed *

9 Transport eyelet, for WEPBA 17-125 Quick,

WEPBA 17-150 Quick (Use only to transport

the machine)*

10 Paddle switch *

11 Additional handle/Additional handle with vibration

damping *

12 Safety cover

13 Support flange

14 2-hole nut *

15 2-hole spanner *

16 Lever for safety guard attachment

* depending on equipment/not in scope of delivery

Before plugging in, check that the rated mains

voltage and mains frequency, as stated on the

rating label, match with your power supply.

Always install an RCD with a max. trip current

of 30 mA upstream.

6.1 Attaching the additional handle

Always work with the additional handle (11)

attached! Attach the additional handle on the

left or right of the machine and secure.

6.2 Attach the safety guard

For safety reasons, always use the safety

guard provided for the respective wheel! See

also chapter11.Accessories!

Safety guard for grinding

Designed for work with roughing wheels, flap

sanding pads, diamond cut-off wheels.

See illustration D on page 2.

- Push and hold the lever (16). Place the safety

guard (12) in the position indicated.

- Release the lever and turn the safety guard until

the lever engages.

- Push the lever and turn the safety guard until the

closed section is facing the operator.

- Make sure that the guard is placed securely: The

lever must engage and you should not be able to

turn the safety guard.

Use only accessories that

are covered by at least

3.4 mm by the safety guard.

(Disassemble in reverse order.)

Prior to any conversion work: Pull the mains

plug from the socket. The machine must be

switched off and the spindle at a standstill.

For reasons of safety, attach the parting guard

before performing parting work (see chapter

11. Accessories).

7.1 Locking the spindle

- Press in the spindle locking button (4) and turn the

spindle (2) by hand until the spindle locking button

engages.

7.2 Placing the grinding wheel in position

WA..., WBA..., WE...A...:

See illustration A on page 2.

The Autobalancer support flange (3) is

permanently fitted on the spindle. As is the

case with most other angle grinders, a detachable

support flange is not necessary.

The contact surfaces of the Autobalancer

support flange (3), grinding wheel and the

"Quick" clamping nut (1) must be clean. Clean if

necessary.

- Place the grinding wheel on the Autobalancer

support flange (3).

The grinding wheel must lie flat on the

Autobalancer supporting flange.

WPB...:

See illustration B on page 2.

- Fit the support flange (13) on the spindle. The

flange should not turn on the spindle when

properly attached.

- Place the grinding disc on the support flange (13).

The grinding disc must lay flat on the supporting

flange.

5. Overview

6. Commissioning

7. Attaching the grinding disc

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Metabo WEVA 15-150 Quick in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,95 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Metabo WEVA 15-150 Quick Manual

Product: