Manual Metabo WEPBA 17-125 Quick (page 18 of 124) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

595532

Zoom out

Zoom in

1/124

ENGLISHen

7.3 Securing/Releasing the "Quick"

clamping nut (depending on features)

Securing the "Quick" clamping nut (1):

Only attach the "Quick" clamping nut (1) to

tools with "Metabo Quick System". These

tools can be identified by the red spindle lock button

(4) with "M-Quick" logo

Do not use the "Quick" clamping nut if the

accessory has a clamping shank thicker than

6.8 mm! In this case, use the 2-hole nut (14) with 2-

hole spanner (15).

- Lock the spindle (see chapter 7.1).

- Position the "Quick" clamping nut (1) on the

spindle (2) so that the 2 lugs engage in the 2

grooves on the spindle. See illustration on page 2.

- Tighten the "Quick"clamping nut by turning

clockwise by hand.

- Turn the grinding wheel firmly clockwise to tighten

the "Quick"clamping nut.

Releasing the clamping nut (1):

Only when the "Quick" clamping nut (1) is

attached must the spindle be stopped using

the red M-Quick spindle locking button (4)!

- The machine continues to run after switching off.

- Press in the M-Quick spindle locking button (4)

just before the grinding disc stops. The "Quick"

clamping nut (1) loosens itself by around half a

turn and can be removed without additional effort

or tools.

7.4 Securing/Releasing the 2-hole nut

(depending on features)

Due to safety reasons, the nut with two holes

(14) must not be used for machines with the

designation W..B...

The 2 sides of the 2-hole nut are different. Screw the

2-hole nut onto the spindle as follows:

See illustration C on page 2.

- X) For thin grinding discs:

The edge of the 2-hole nut (14) faces upwards so

that the thin grinding disc can be attached

securely.

Y) For thick grinding discs:

The edge of the 2-hole nut (14) faces downwards

so that the 2-hole nut can be attached securely to

the spindle.

- Locking the spindle. Turn the 2-hole nut (14)

clockwise using the 2-hole spanner (15) to secure.

Releasing the 2-hole nut:

- Lock the spindle (see chapter 7.1). Turn the 2-hole

nut (14) anticlockwise using the 2-hole spanner

(15) to unscrew.

8.1 Adjusting the speed (depending on

features)

Set the recommended speed at the thumbwheel

(8). (small number = low speed; large number =

high speed)

Cutting disc, roughing disc, cup wheel and diamond

cutting disc: high speed

Brush: medium speed

Sanding plate: low to medium speed

Note:

We recommend using our angle polisher for

polishing work.

8.2 Switching On and Off

Always guide the machine with both hands.

Switch on first, then guide the accessory

towards the workpiece.

Avoid inadvertent starts: always switch the

tool off when the plug is removed from the

mains socket or if there has been a power cut.

WA..., WBA..., WEA..., WEVA..., WEBA...: In

continuous operation, the machine continues

running if it is forced out of your hands. Therefore,

always hold the machine with both hands using the

handles provided, stand securely and concentrate.

Avoid the machine swirling up or taking in dust

and chips. After switching off the machine,

only place it down when the motor has come to a

standstill.

Machines with slide switch:

Switching on: Push the slide switch (5) forward.

For continuous activation, now tilt

downwards until it engages.

Switching off: Press the rear end of the slide

switch (5) and release it.

Machines with paddle switch

(with dead man function):

Switching on: : Slide paddle switch (10) in the

direction of the arrow and then press the

paddle switch (10).

Switching off: Release the paddle switch (10).

8.3 Working Directions

Grinding and sanding operations:

Press down the machine evenly on the surface and

move back and forth so that the surface of the

workpiece does not become too hot.

8. Use

1010

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Metabo WEPBA 17-125 Quick in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,95 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Metabo WEPBA 17-125 Quick Manual

Product: