625646
17
Zoom out
Zoom in
Previous page
1/112
Next page
ENGLISH en
17
Note: We recommend using our angle polisher for
polishing work.
8.2 Switching On and Off
Always guide the machine with both hands.
Switch on first, then guide the accessory
towards the workpiece.
The machine must not be allowed to draw in
additional dust and shavings. When switching
the machine on and off, keep it away from dust
deposits. After switching off the machine, only place
it down when the motor has come to a standstill.
Avoid inadvertent starts: always switch the
tool off when the plug is removed from the
mains socket or if there has been a power cut.
In continuous operation, the machine
continues running if it is forced out of your
hands. Therefore, always hold the machine with
both hands using the handles provided, stand
securely and concentrate.
Machines with slide switch:
Switching on: Push the sliding switch (8) forward.
For continuous activation, now tilt
downwards until it engages.
Switching off: Press the rear end of the sliding
switch (8) and release the sliding switch.
WEPF 15-150 Quick:
"Paddle switch" (with dead man's function):
Switching on: Slide the switch-on lock (12) in the
direction of the arrow and press the trigger
switch (13).
Switching off: Release the trigger switch (13).
WEPBF 15-150 Quick:
"Paddle switch" (with dead man's function):
Switching on: Slide the trigger switch (13) in the
direction of the arrow and press the trigger
switch (13).
Switching off: Release the trigger switch (13).
8.3 Working Directions
Grinding and sanding operations:
Press down the machine evenly on the surface and
move back and forth so that the surface of the
workpiece does not become too hot.
Rough grinding: position the machine at an angle of
30° - 40° for the best working results.
Cut-off grinding:
Always work against the run of the disc
(see illustration). Otherwise there is
the danger of the machine kicking
back from the cut out of control. Guide
the machine evenly at a speed
suitable for the material being processed. Do not tilt,
apply excessive force or sway from side to side.
Wire brushing:
Press down the machine evenly.
8.4 Rotate gear housing
See illustration D on page 3.
- Disconnect the mains plug.
- Remove guard (6).
- Unscrew the 4 gear housing screws (a).
CAUTION! Do not remove the gear housing!
- Turn the gear housing to the desired position
without removing it.
- Screw in the 4 gear housing screws (a) in the
available threads! Tightening torque = 3,0 Nm +/-
0,3 Nm.
It is possible that particles deposit inside the power
tool during operation. This impairs the cooling of the
power tool. Conductive build-up can impair the
protective insulation of the power tool and cause
electrical hazards.
The power tool should be cleaned regularly, often
and thoroughly through all front and rear air vents
using a vacuum cleaner or by blowing in dry air.
Prior to this operation, separate the power tool from
the power source and wear protective glasses and
dust mask.
Regularly clean dust filter: remove and blow out
with compressed air.
- Electronic safety shutdown The electronic
signal display (10) flashes and the machine
was automatically SWITCHED OFF. If the slew
rate of the current is too high (for example, if the
machine suddenly seizes or kickback occurs), the
machine switches off. Switch machine off with
switch. Switch it on again and continue to work as
normal. Try to prevent the machine from seizing.
See chapter 4.2.
Machines with VTC and TC electronics:
The electronic signal display (10) lights
up and the load speed decreases. There is
too much load on the machine! Run the
machine in idling until the electronics signal
indicator switches off.
Machines with VTC, TC and VC electronics:
The electronic signal display (10) flashes
and the machine does not start. The restart
protection is active. If the mains plug is
0
I
8
0
I
121212 131313
0
I
1010
13
9. Cleaning
10. Troubleshooting
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo WEF 15-150 Quick at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo WEF 15-150 Quick in the language / languages: All languages as an attachment in your email.

The manual is 6,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info