599582

Metabo WE 24-230 MVT Manual

16
Zoom out
Zoom in
Previous page
1/121
Next page
ENGLISHen
16
See page 2.
1"Quick"clamping nut *
2Support flange *
3Spindle
4WE
A
...: Autobalancer support flange (non-
detachable) *
5 Spindle locking button
6 Electronic signal indicator *
7 Lock (to prevent the machine from being
switched on unintentionally, or for continuous
operation)*
8 Trigger (for switching on and off)
9 Button (to turn the main handle)
10 Main handle
11 Additional handle/Additional handle with
vibration damping
12 Safety cover
13 Adjusting nut *
14 2-hole spanner *
15 Quick-release clamp (to adjust safety guard
without the use of tools)
16 Screw (to adjust clamping force of quick-
release clamp)
* depending on equipment/not in scope of delivery
Before plugging in, check that the rated mains
voltage and mains frequency, as stated on the
rating label, match with your power supply.
Always install an RCD with a max. trip current
of 30 mA upstream.
Use only extension cables with a min. cross-section
of 1.5 mm
2
. Extension cables must correspond to
the power consumption of the machine (cf
Technical Specifications). If a cable roller is used,
always roll up the cable completely.
6.1 Attaching the additional handle
Always work with the additional handle (11)
attached! Manually screw in the additional
handle securely in the left, centre or right threaded
hole (depending on requirements).
6.2 Attach the safety guard
(for working with abrasive discs)
Prior to operation: Attach safety
guard.
For reasons of safety, the safety guard (12)
should always be attached when roughing
work is performed.
For reasons of safety, the special parting
guard should always be attached before
parting work is performed (see chapter 11.
Accessories).
See illustration E on page 2.
- Open quick-release clamp (15). Mount the safety
guard (12) in the position indicated.
- Turn the safety guard until the closed section is
facing the operator.
- Close quick-release clamp.
- If necessary, increase clamping force of quick-
release clamp by tightening the screw (16) (with
opened quick-release clamp).
Use only accessories that
are covered by at least
3.4 mm by the safety guard.
6.3 Pivotable main handle
Only work with the main handle (10) engaged.
See illustration B on page 2.
- Push in the button (9).
- The main handle (10) can now be turned 90° to
both sides and can be engaged.
- Make sure that it is securely positioned: the main
handle (10) must be engaged and it should not be
possible to move it.
6.4 Power-supply connection
The mains sockets must be protected using time-
delay fuses or circuit breakers.
Machines with "WE..." in the model designation:
(with inbuilt automatic startup-current limitation(soft
start).) The mains sockets can also be protected
using fast-acting fuses or circuit breakers.
Prior to any conversion work: Pull the mains
plug from the socket. The machine must be
switched off and the spindle at a standstill.
For reasons of safety, attach the parting guard
before performing parting work (see chapter
11. Accessories).
7.1 Locking the spindle
Press in the spindle locking button (5) only
when the spindle is stationary!
- Press in the spindle locking button (5) and
turn the spindle (3) by hand until the spindle
locking button engages.
7.2 Placing the grinding wheel in position
See illustration C on page 2.
Machines with the designation W 2..., WE 2...:
- Fit the support flange (2) on the spindle. The
flange should not turn on the spindle when
properly attached.
- Position the grinding wheel on the support flange
(2) as shown in illustration C.
The grinding disc must lay flat on the supporting
flange.
Machines with the designation WEA 2...:
The Autobalancer support flange (4) is
permanently fitted on the spindle. As is the
case with most other angle grinders, a detachable
support flange is not necessary.
5. Overview
6. Commissioning
7. Attaching the grinding disc
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo WE 24-230 MVT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo WE 24-230 MVT in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info