599573

Metabo WE 24-230 MVT Quick Manual

18
Zoom out
Zoom in
Previous page
1/121
Next page
ENGLISHen
18
using a vacuum cleaner or by blowing in dry air.
Prior to this operation, separate the power tool from
the power source and wear protective glasses and
dust mask.
Button (9) for adjusting the handle: Occasionally
blow compressed air through the button (when
pressed, in all 3 main handle positions). Prior to this
operation, separate the power tool from the power
source and wear protective glasses and dust mask.
Machine with "WE..." in the model designation:
- Overload protection: The electronic signal
display (6) lights up and the load speed
decreases dramatically. The motor temperature
is too high! Run the machine in idling until it cools
down and the electronic signal display switches
off.
- Overload protection: The electronic signal
display (6) lights up and the load speed
decreases slightly. The machine is overloaded.
Work with a reduced load until the electronic
signal display goes out.
- Electronic safety stop: The electronic signal
display (6) lights up and the machine was
SWITCHED OFF automatically. If the slew rate
of the current is too high (for example, if the
machine suddenly seizes or kickback occurs), the
machine switches off. Switch off the machine at
the trigger switch (8). Switch it on again and
continue to work as normal. Try to prevent the
machine from seizing. See Section 4.2.
- Restart protection: The electronic signal
display (6) FLASHES and the machine does
not start. The restart protection is active. If the
mains plug is inserted with the machine switched
on, or if the power supply is restored following an
interruption, the machine does not start up. Switch
the machine off and on again.
- When switched on, the machine accelerates
to maximum speed very quickly, i.e. automatic
restriction of the starting current does not work
(soft start). An electronic error exists. Other
safety-related electronic functions are no longer
available. Have the machine repaired immediately
(see 12.).
W 22-180 MVT, W 22-230 MVT, W 24-180 MVT,
W 24-230 MVT, W 26-180 MVT, W 26-230 MVT:
- Switching on the machine reduces the voltage
briefly. Unfavourable mains power conditions may
have a detrimental effect on other machines.
Power impedances less than 0.2 ohm should not
cause malfunctions.
Use only genuine Metabo accessories.
Use only accessories which fulfil the requirements
and specifications listed in these operating
instructions.
Fit accessories securely. Secure the machine if it is
operated in a bracket. Loss of control can cause
personal injury.
See page 4.
A Roughing disc (always use with safety guard
attached)
B Lamellar grinding disc (always use with safety
guard attached)
C Parting safety guard.
D Parting disc (always use with parting safety
guard attached)
E Diamond discs (always use with safety guard or
parting safety guard attached)
F Parting safety guard with guide slot (place on
machine and secure with screws.) (with adapter
for connection to a suitable dust extractor for
extraction of stone dust generated when cutting
stone slabs.)
G Hand guard (for attaching under the additional
side-mounted handle.)
H Extension piece (for working with supporting
discs. Increases the distance between the
spindle and the supporting disc by approx. 35
mm)
I Supporting disc for fibre discs (always attach
using the supporting disc clamping nut
supplied.) (always use with the hand guard
attached.)
J Fibre discs (always use with the hand guard
attached.)
K Steel wire brushes (always use with the hand
guard attached.)
L Bench cut-off stand
M Adjusting nut (13)
N "Quick" clamping nut (1)
For the complete range of accessories, see
www.metabo.com or the main catalogue.
Repairs to electrical tools must be carried out
by qualified electricians ONLY!
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. For
addresses see www.metabo.com.
You can download a list of spare parts from
www.metabo.com.
The generated grinding dust may contain harmful
substances. Dispose appropriately.
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Only for EU countries: Never dispose of
power tools in your household waste! In
accordance with European Directive 2002/
96/EC on waste electrical and electronic equipment
and its implementation in national legal systems,
used power tools must be collected separately and
handed in for environmentally compatible recycling.
10. Troubleshooting
11. Accessories
12. Repairs
13. Environmental Protection
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo WE 24-230 MVT Quick at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo WE 24-230 MVT Quick in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info