Manual Metabo WE 22-180 MVT (page 16 of 121) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

599579

Zoom out

Zoom in

1/121

ENGLISHen

See page 2.

1"Quick"clamping nut *

2Support flange *

3Spindle

4WE

...: Autobalancer support flange (non-

detachable) *

5 Spindle locking button

6 Electronic signal indicator *

7 Lock (to prevent the machine from being

switched on unintentionally, or for continuous

operation)*

8 Trigger (for switching on and off)

9 Button (to turn the main handle)

10 Main handle

11 Additional handle/Additional handle with

vibration damping

12 Safety cover

13 Adjusting nut *

14 2-hole spanner *

15 Quick-release clamp (to adjust safety guard

without the use of tools)

16 Screw (to adjust clamping force of quick-

release clamp)

* depending on equipment/not in scope of delivery

Before plugging in, check that the rated mains

voltage and mains frequency, as stated on the

rating label, match with your power supply.

Always install an RCD with a max. trip current

of 30 mA upstream.

Use only extension cables with a min. cross-section

of 1.5 mm

. Extension cables must correspond to

the power consumption of the machine (cf

Technical Specifications). If a cable roller is used,

always roll up the cable completely.

6.1 Attaching the additional handle

Always work with the additional handle (11)

attached! Manually screw in the additional

handle securely in the left, centre or right threaded

hole (depending on requirements).

6.2 Attach the safety guard

(for working with abrasive discs)

Prior to operation: Attach safety

guard.

For reasons of safety, the safety guard (12)

should always be attached when roughing

work is performed.

For reasons of safety, the special parting

guard should always be attached before

parting work is performed (see chapter 11.

Accessories).

See illustration E on page 2.

- Open quick-release clamp (15). Mount the safety

guard (12) in the position indicated.

- Turn the safety guard until the closed section is

facing the operator.

- Close quick-release clamp.

- If necessary, increase clamping force of quick-

release clamp by tightening the screw (16) (with

opened quick-release clamp).

Use only accessories that

are covered by at least

3.4 mm by the safety guard.

6.3 Pivotable main handle

Only work with the main handle (10) engaged.

See illustration B on page 2.

- Push in the button (9).

- The main handle (10) can now be turned 90° to

both sides and can be engaged.

- Make sure that it is securely positioned: the main

handle (10) must be engaged and it should not be

possible to move it.

6.4 Power-supply connection

The mains sockets must be protected using time-

delay fuses or circuit breakers.

Machines with "WE..." in the model designation:

(with inbuilt automatic startup-current limitation(soft

start).) The mains sockets can also be protected

using fast-acting fuses or circuit breakers.

Prior to any conversion work: Pull the mains

plug from the socket. The machine must be

switched off and the spindle at a standstill.

For reasons of safety, attach the parting guard

before performing parting work (see chapter

11. Accessories).

7.1 Locking the spindle

Press in the spindle locking button (5) only

when the spindle is stationary!

- Press in the spindle locking button (5) and

turn the spindle (3) by hand until the spindle

locking button engages.

7.2 Placing the grinding wheel in position

See illustration C on page 2.

Machines with the designation W 2..., WE 2...:

- Fit the support flange (2) on the spindle. The

flange should not turn on the spindle when

properly attached.

- Position the grinding wheel on the support flange

(2) as shown in illustration C.

The grinding disc must lay flat on the supporting

flange.

Machines with the designation WEA 2...:

The Autobalancer support flange (4) is

permanently fitted on the spindle. As is the

case with most other angle grinders, a detachable

support flange is not necessary.

5. Overview

6. Commissioning

7. Attaching the grinding disc

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Metabo WE 22-180 MVT in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5,06 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Metabo WE 22-180 MVT Manual

Product: