595493
18
Zoom out
Zoom in
Previous page
1/124
Next page
ENGLISHen
18
Collect the generated particles at the source, avoid
deposits in the surrounding area.
Use suitable accessories for special work (see
chapter 11.), thus less particles enter the
environment in an uncontrolled manner.
Use a suitable extraction unit.
Reduce dust exposure with the following measures:
- Do not direct the escaping particles and the
exhaust air stream at yourself or nearby persons
or on dust deposits.
- Use an extraction unit and/or air purifiers
- Ensure good ventilation of the workplace and
keep clean using a vacuum cleaner Sweeping or
blowing stirs up dust
- Vacuum or wash the protective clothing Do not
blow, beat or brush
See page 2.
1"Quick"clamping nut *
2 Support flange
3Spindle
4 Spindle locking button
5 Sliding on/off switch *
6Handle
7 Electronic signal indicator *
8 Thumbwheel for selection of speed *
9 Trigger *
10 Switch-on lock
11 Additional handle/Additional handle with vibration
damping *
12 Safety cover
13 2-hole nut *
14 2-hole spanner *
15 Lever for safety guard attachment
* depending on equipment/not in scope of delivery
Before plugging in, check to see that the rated
mains voltage and mains frequency, as stated
on the rating label, match with your power supply.
Always install an RCD with a max. trip current
of 30 mA upstream.
6.1 Attaching the additional handle
Always work with the additional handle
attached! (11) Attach the additional handle on
the left or right of the machine and secure.
6.2 Attach the safety guard
For safety reasons, always use the safety
guard provided for the respective wheel! See
also chapter11.Accessories!
Safety guard for grinding
Designed for work with roughing wheels, flap
sanding pads, diamond cut-off wheels.
See illustration C on page 2.
- Push and hold the lever. (15) Place the safety
guard in the position indicated. (12)
- Release the lever and turn the safety guard until
the lever engages.
- Push the lever and turn the safety guard until the
closed section is facing the operator.
- Make sure that the guard is placed securely: The
lever must engage and you should not be able to
turn the safety guard.
Use only accessories that
are covered by at least 3.4
mm by the safety guard.
(Disassemble in reverse order.)
Prior to any conversion work: Pull the mains
plug from the socket. The machine must be
switched off and the spindle at a standstill.
For reasons of safety, attach the cutting guard
before performing cutting-off operations (see
chapter Accessories).11.
7.1 Locking the spindle
- Press in the spindle locking button and turn the
spindle by hand until the spindle locking button
engages. (4) (3)
7.2 Placing the grinding wheel in position
See illustration A on page 2.
- Fit the support flange on the spindle. (2) The
flange should not turn on the spindle when
properly attached.
Only W 9-100: Screw support flange with two-hole
spanner onto spindle so that the small collar (with
diameter 16 mm) is facing upwards.
- Place the grinding disc on the support flange. (2)
The grinding disc must lay flat on the supporting
flange.
7.3 Securing/Releasing the "Quick"
clamping nut (depending on features)
Securing the (1)"Quick" clamping nut:
Only attach the "Quick" clamping nut (1) to
tools with "Metabo Quick System". These
tools can be identified by the red spindle lock button
(4) with "M-Quick" logo
Do not use the "Quick" clamping nut if the
accessory has a clamping shank thicker than
6.8 mm! In this case, use the 2-hole nut (13) with 2-
hole spanner (14).
- Lock the spindle (see chapter 7.1).
- Position the "Quick" clamping nut on the spindle
so that the 2 lugs engage in the 2 grooves on the
spindle. (1) (3) See illustration on page 2.
- Tighten the "Quick"clamping nut by turning
clockwise by hand.
-Turn the grinding wheel firmly clockwise to tighten
the "Quick"clamping nut.
5. Overview
6. Commissioning
7. Attaching the grinding disc
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo WE 15-150 Quick at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo WE 15-150 Quick in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,99 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info