599561

Metabo WE 1450-150 RT Manual

15
Zoom out
Zoom in
Previous page
1/108
Next page
ENGLISH en
15
7 Lock (to prevent the machine from being switched
on unintentionally, or for continuous operation) *
8
Trigger (
for switching on and off) *
9 Additional handle
10 Safety cover
11 Clamping nut *
12 2-hole spanner *
13 Clamping screw
* depending on equipment/not in scope of delivery
Before plugging in, check to see that the rated
mains voltage and mains frequency,
as stated on the rating label, match your power
supply.
6.1 Attaching the additional handle
Always work with the additional handle
attached (9)! Attach the additional handle
on the left or right of the machine and secure.
6.2 Install safety guard
For safety reasons, always use the safety
guard provided for the respective wheel! See
also chapter 11.
Safety guard for grinding
Designed for work with roughing wheels, flap
sanding pads, diamond cut-off wheels.
See page 2, illustration C.
- Slacken the screw (13). Place the safety guard
(10) in the position indicated.
- Turn the safety guard until the closed section is
facing the operator.
- Tighten the screw (13), ensuring that the anti-twist
device engages in the slots.
- Make sure that the guard is seated securely: you
should not be able to turn the safety guard.
Use only accessories that
are covered by at least
3.4 mm by the safety guard.
Disconnect the mains plug before changing
any accessories. The machine must be
switched off and the spindle at a standstill.
For reasons of safety, attach the parting guard
before performing parting work
(see chapter 11. Accessories).
7.1 Locking the spindle
- Press in the spindle locking button (5) and turn the
spindle (4) by hand until the spindle locking button
engages.
7.2 Placing the grinding wheel in position
See page 2, illustration A.
- Place the supporting flange (3) on the spindle (see
illustration above). The flange should not turn on
the spindle when properly attached.
- Place the grinding wheel on the
support flange (3) (see illustration above).
The grinding wheel must lay flat on the supporting
flange. The metal flange on the parting grinder
disc must lay flat on the support flange.
Note:
The support flange (3) is secured to prevent it
from falling off. To remove: use some force if
necessary.
7.3 Securing/releasing the (tool-free)
clamping nut (depending on features)
Only tighten the (tool-free) clamping nut (2)
manually.
For the machine to operate, the clip (1) must
always lie flat on
clamping nut (2)
.
To secure the (tool-free) clamping nut (2):
Do not use the
(tool-free) clamping nut if the
accessory has a clamping shank thicker than 6
mm
! In this case, use the
clamping nut (11) with 2-
hole spanner (12).
- Lock the spindle (see chapter 7.1).
- Flip up the clip
(1)
on the clamping nut.
- Fit the clamping nut (2) on the spindle (4). See
illustration on page 2.
-
(1)Tighten the
clamping nut on the clip manually
in a clockwise direction.
- Flip down the clip
(1) again
.
To release the (tool-free) clamping nut (2)
:
- Lock the spindle (see chapter 7.1).
- Flip up the clip
(1)
on the clamping nut.
- Unscrew the clamping nut
(2)
, turning it
anticlockwise manually .
Note:
If the clamping nut is very tightly secured
(2),
you can also use a 2-hole spanner
to unscrew it.
7.4 Securing/releasing the clamping nut
(depending on features)
Securing the clamping nut (11):
The 2 sides of the clamping nut are different. Screw
the clamping nut onto the spindle as follows:
See page 2, illustration B.
- A) For thin grinding wheels:
The edge of the clamping nut (11) faces upwards
so that the thin grinding wheel can be attached
securely.
B) For thick grinding wheels:
The edge of the clamping nut (11) faces
downwards so that the clamping nut can be
attached securely to the spindle.
- Lock the spindle. Turn the clamping nut (11)
clockwise using the 2-hole spanner (12) to
secure.
Releasing the clamping nut:
- Lock the spindle (see chapter 7.1). Turn the
clamping nut (11) anticlockwise using the 2-hole
spanner (12) to unscrew.
6. Commissioning
7. Attaching the grinding wheel
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo WE 1450-150 RT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo WE 1450-150 RT in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info