595456

Metabo WB 18 LTX BL 150 Quick Manual

17
Zoom out
Zoom in
Previous page
1/120
Next page
ENGLISH en
17
For reasons of safety, attach the parting guard
before performing parting work (see chapter
11. Accessories).
7.1 Locking the spindle
- Press in the spindle locking button (5) and turn the
spindle
(4) by hand until you feel the spindle locking
button engage.
7.2 Placing the grinding wheel in position
See illustration C on page 2.
- Fit the support flange (3) on the spindle. The
flange should not turn on the spindle when
properly attached.
- Place the grinding wheel on the support flange (3).
The grinding wheel must lay flat on the supporting
flange. The metal flange on the parting grinder
disc must lay flat on the support flange.
Note:
The support flange (3) is secured to prevent it
from falling off. To remove: use some force if
necessary.
7.3 Securing/releasing the (tool-free)
clamping nut (depending on features)
Only tighten the (tool-free) clamping nut (2)
manually.
For the machine to operate, the clip (1) must
always lie flat on
clamping nut (2)
.
To secure the (tool-free) clamping nut (2):
Do not use the
(tool-free) clamping nut if the
accessory has a clamping shank thicker than 6
mm
! In this case, use the
clamping nut (17) with 2-
hole spanner (18).
- Lock the spindle (see chapter 7.1).
- Flip up the clip
(1)
on the clamping nut.
- Fit the clamping nut (2) on the spindle (4). See
illustration on page 2.
-
(1)Tighten the
clamping nut on the clip manually
in a clockwise direction.
- Flip down the clip
(1) again
.
To release the (tool-free) clamping nut (2)
:
- Lock the spindle (see chapter 7.1).
- Flip up the clip
(1)
on the clamping nut.
- Unscrew the clamping nut
(2)
, turning it
anticlockwise manually .
Note:
If the clamping nut is very tightly secured
(2),
you can also use a 2-hole spanner
to unscrew it.
7.4 Securing/releasing the clamping nut
(depending on features)
Due to safety reasons, the nut with two holes
(17) must not be used for machines with the
designation W..B...
Securing the clamping nut (17):
The 2 sides of the clamping nut are different. Screw
the clamping nut onto the spindle as follows:
See illustration D on page 2.
- A) For thin grinding wheels:
The edge of the clamping nut (17) faces upwards
so that the thin grinding wheel can be attached
securely.
B) For thick grinding wheels:
The edge of the clamping nut (17) faces
downwards so that the clamping nut can be
attached securely to the spindle.
- Lock the spindle. Turn the clamping nut (17)
clockwise using the 2-hole spanner (18) to
secure.
Releasing the clamping nut:
- Lock the spindle (see chapter 7.1). Turn the
clamping nut (17) anticlockwise using the 2-hole
spanner (18) to unscrew.
8.1 Switching On and Off
Always guide the machine with both hands.
Switch on first, then guide the
accessory
towards the workpiece.
The machine must not be allowed to draw in
additional dust and shavings. When switching
the machine on and off, keep it away from dust
deposits. After switching off the machine, only place
it down when the motor has come to a standstill.
Avoid switching on the machine accidentally:
always switch it off when the battery pack is
removed from the machine.
In continuous operation, the machine
continues running if it is forced out of your
hands. Therefore, always hold the machine with
both hands using the handles provided, stand in a
safe position and concentrate.
Machines with slide switch:
Switching on: Push the slide switch (6) forward.
For continuous activation, now tilt
downwards until it engages.
Switching off: Press the rear end of the slide
switch (6) and release.
Machines with Paddle Switch
(with dead man function):
(machines with the designation WP...)
Switching on: Slide the switch-on lock (13) in
the direction of the arrow and press
the trigger (14).
Switching off: Release the trigger (14).
8. Use
0
I
6
0
I
14 13
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo WB 18 LTX BL 150 Quick at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo WB 18 LTX BL 150 Quick in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info