Manual Metabo WB 11-125 Quick (page 13 of 104) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

665553

Zoom out

Zoom in

1/104

ENGLISH en

4.5 Safety Warnings Specific for Sanding

Operations:

a) Do not use excessively oversized sanding

disc paper. Follow manufacturer's recommen-

dations when selecting sanding paper. Larger

sanding paper extending beyond the sanding pad

presents a laceration hazard and may cause snag-

ging, tearing of the disc or kickback.

4.6 Safety Warnings Specific for Wire Brush-

ing Operations:

a) Be aware that wire bristles are thrown by the

brush even during ordinary operation. Do not

overstress the wires by applying excessive

load to the brush. The wire bristles can easily

penetrate light clothing and/or skin.

b) If the use of a guard is recommended for wire

brushing, do not allow any interference of the

wire wheel or brush with the guard. Wire wheel

or brush may expand in diameter due to work load

and centrifugal forces.

4.7 Additional Safety Instructions

WARNING – Always wear protective

goggles.

Use elastic cushioning layers if they have been

supplied with the abrasive and if required.

Observe the specifications of the tool or accessory

manufacturer! Protect the discs from grease or

impacts!

Grinding discs must be stored and handled with

care in accordance with the manufacturer's instruc-

tions.

Never use parting grinder discs for roughing work!

Do not apply pressure to the side of parting grinder

discs.

The workpiece must lay flat and be secured against

slipping, e.g. using clamps. Large workpieces must

be sufficiently supported.

If accessories with threaded inserts are used, the

end of the spindle may not touch the base of the

hole on the grinding tool. Make sure that the thread

in the accessory is long enough to accommodate

the full length of the spindle. The thread in the

accessory must match the thread on the spindle.

See page 2 and chapter 14. Technical Specifica-

tions for more information on the spindle length and

thread.

During machining, of metals in

particular, conductive dust can form

deposits inside the machine. This can lead to the

transfer of electrical energy onto the machine

housing. This can mean a temporary danger of

electric shocks. This is why it is necessary when the

machine is running to blow compressed air through

the rear ventilation slots of the machine regularly,

frequently and thoroughly. Here, the machine must

be held firmly.

We recommend using a stationary extractor system

and connecting a residual current circuit-breaker

(FI) upstream. When the angle grinder is shut down

via the FI circuit breaker, it must be checked and

cleaned. For information on cleaning the motor, see

chapter 9. Cleaning.

Dust from material such as paint containing lead,

some wood species, minerals and metal may be

harmful. Contact with or inhalation of the dust may

cause allergic reactions and/or respiratory diseases

to the operator or bystanders.

Certain kinds of dust are classified as carcinogenic

such as oak and beech dust especially in

conjunction with additives for wood conditioning

(chromate, wood preservative). Material containing

asbestos must only be treated by specialists.

- Where the use of a dust extraction device is

possible it shall be used.

- The work place must be well ventilated.

- The use of a dust mask of filter class P2 is recom-

mended.

Follow national requirements for the materials you

want to work with.

Materials that generate dusts or vapours that may

be harmful to health (e.g. asbestos) must not be

processed.

When working in dusty conditions, ensure that

ventilation openings are not blocked. If it becomes

necessary to remove dust, first disconnect the

power tool from the mains supply (use non-metallic

objects) and avoid damaging internal components.

Damaged, eccentric or vibrating tools must not be

used.

Avoid damage to gas or water pipes, electrical

cables and load-bearing walls (static).

Connect a FI circuit-breaker with max.

release current (30 mA) upstream when using the

machine outdoors!

Pull the plug out of the socket before making any

adjustments, converting or servicing the machine.

Metabo S-automatic safety clutch. When the safety

clutch responds, switch off the machine immedi-

ately!

A damaged or cracked auxiliary handle must be

replaced. Never operate a machine with a defective

additional handle.

A damaged or cracked safety guard must be

replaced. Never operate a machine with a defective

safety guard.

This power tool is not suitable for polishing work.

Improper use of the machine will void the warranty!

The motor may overheat and damage the electric

power tool. We recommend using our angle

polisher for polishing work.

See page 2.

1"Quick"clamping nut

2Spindle

Autobalancer support flange (non-detachable)*

4 Spindle locking button

5 Sliding

on/off switch *

6 Electronic signal indicator*

7"Protect"

safety switch

5. Overview

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Metabo WB 11-125 Quick in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,17 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Metabo WB 11-125 Quick Manual

Product: