Manual Metabo W 9-125 Quick (page 20 of 124) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

595484

Zoom out

Zoom in

1/124

ENGLISHen

- Slide the spring that pushes the lever in position to

the side and re-insert the lever (15) (with its sheet

metal part), and fix with the fastening screw (a).

Tightening torque = 5.0 Nm +/- 0.5 Nm. Check the

lever for correct function: it has to be under spring

tension.

It is possible that particles deposit inside the power

tool during operation. This impairs the cooling of

the power tool. Conductive build-up can impair the

protective insulation of the power tool and cause

electrical hazards.

The power tool should be cleaned regularly, often

and thoroughly through all front and rear air vents

using a vacuum cleaner or by blowing in dry air.

Prior to this operation, separate the power tool from

the power source and wear protective glasses and

dust mask.

Machines with VTC and TC electronics:

The electronic signal display lights up

and the load speed decreases. (7) There is

too much load on the machine! Run the

machine in idling until the electronics signal

indicator switches off.

The machine does not start. The

electronic signal display (7) (depends on

model) flashes. The restart protection is

active. If the mains plug is inserted with the machine

switched on, or if the power supply is restored

following an interruption, the machine does not start

up. Switch the machine off and on again.

Use only genuine Metabo accessories.

See page 6.

Use only accessories which fulfil the requirements

and specifications listed in these operating

instructions.

A Cutting guard clip / guard for cut-off

grinding

Designed for work with cutting disc and diamond

cutting discs. Once the cutting guard clip is fitted,

the safety guard becomes a cutting guard.

B Extraction guard for cut-off grinding

Designed for cutting through stone slabs with

diamond cutting discs. With nozzle for extracting

stone dust using a suitable extraction unit.

C Extraction guard for surface grinding

Intended for grinding of concrete, screed, wood and

plastics with diamond cup wheels and/or fibre discs

and suitable sanding plates. With nozzle for

extracting stone, wood and plastic dust using a

suitable extraction unit. Not suitable for extracting

sparks or for grinding of metals.

D Dust filter

The fine mesh filter prevents coarse particles from

entering the motor housing. Remove regularly and

clean.

E Hand protection

Intended for work with backing pads, sanding

plates, wire brushes and support plates, sanding

pads, wire brushes and diamond Drill Bits for tiles.

Install hand guard under the additional side-

mounted handle.

F Multiple position bar for side handle

Permits numerous handle positions.

G Bar side handle

For a complete range of accessories, see

www.metabo.com or the catalogue.

Repairs to electrical tools must be carried out

by qualified electricians ONLY!

If the connection lead is damaged, it must be

replaced by a special connection lead.

Contact your local Metabo representative if you

have Metabo power tools requiring repairs. For

addresses see www.metabo.com.

You can download a list of spare parts from

www.metabo.com.

The generated grinding dust may contain harmful

substances. Dispose appropriately.

Observe national regulations on environmentally

compatible disposal and on the recycling of disused

machines, packaging and accessories.

Only for EU countries: Never dispose of

power tools in your household waste! In

accordance with European Directive 2002/

96/EC relating to electrical and electronic waste and

implementation of national law, used electrical tools

must be collected separately and disposed of in an

environmentally friendly manner at recycling

centres.

Explanatory notes on the specifications on page 4.

Changes due to technological progress reserved.

Ø = max. diameter of the accessory

max,1

= max. permitted thickness of the

clamping shank on accessory when

using 2-hole nut (13)

max,2

= max. permitted thickness of clamping

shank on accessory when using

"Quick" clamping nut (1)

max,3

= roughing disc/cutting disc:

max. permitted thickness of accessory

M=spindle thread

l = length of the grinding spindle

n* = no-load speed (maximum speed)

* = no-load speed (adjustable)

=rated input power

9. Cleaning

10. Troubleshooting

11. Accessories

12. Repairs

13. Environmental Protection

14. Technical Specifications

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Metabo W 9-125 Quick in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,99 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Metabo W 9-125 Quick Manual

Product: