665529
16
Zoom out
Zoom in
Previous page
1/108
Next page
ENGLISHen
16
downwards so that the clamping nut can be
attached securely to the spindle.
Z) Only with W 8-100:
The collar of the adjusting nut faces downwards
and/or the flat surface faces upwards.
- Lock the spindle. Turn the clamping nut (12)
clockwise using the 2-hole spanner (13) to secure.
Releasing the clamping nut:
- Lock the spindle (see chapter 7.1). Turn the
clamping nut (12) anticlockwise using the 2-hole
spanner (13) to unscrew.
8.1 Adjusting the speed
(depending on features)
Set the recommended speed at the setting
wheel (7).
Parting grinder and roughing discs, cup wheel,
diamond parting wheel: high speed
Brush: medium speed
Grinding wheel: low to medium speed
Note:
We recommend using our angle polisher for
polishing work.
8.2 Switching On and Off
Always guide the machine with both hands.
Switch on first, then guide the
accessory
towards the workpiece.
The machine must not be allowed to draw in
additional dust and shavings. When switching
the machine on and off, keep it away from dust
deposits. After switching off the machine, only place
it down when the motor has come to a standstill.
Avoid inadvertent starts: always switch the
tool off when the plug is removed from the
mains socket or if there has been a power cut.
In continuous operation, the machine
continues running if it is forced out of your
hands. Therefore, always hold the machine with
both hands using the handles provided, stand in a
safe position and concentrate.
Machines with slide switch:
Switching on: Push the slide switch (5) forward.
For continuous activation, now tilt
downwards until it engages.
Switching off: Press the rear end of the slide
switch (5) and release.
Machines with "Ergo Paddle Switch" (with
dead man function):
(machines with the designation WP..., WEP...)
Switching on: Slide the switch-on lock (8) in
the direction of the arrow and press
the trigger (9).
Switching off: Release the trigger (9).
8.3 Working instructions
Grinding and sanding operations:
Press down the machine evenly on the surface
and move back and forth so that the surface of the
workpiece does not become too hot.
Roughing: position the machine at an angle of 30° -
40° for the best working results.
Separating:
Always work against the run of the disc
(see illustration). Otherwise there is
the danger of the machine kicking
back from the cut out of control. Guide
the machine evenly at a speed
suitable for the material being processed. Do not tilt,
apply excessive force or sway from side to side.
Wire brushing:
Press down the machine evenly.
Motor cleaning: blow compressed air through the
rear ventilation slots of the machine regularly,
frequently and thoroughly. Here, the machine must
be held firmly.
Machines with VTC and TC electronics:
The electronic signal display (6) lights up and
the load speed decreases.
The coil temperature is
too high! Run the machine in idling until the
electronics signal indicator switches off.
Machines with VTC, TC and VC electronics:
The electronic signal display (6) flashes
and the machine does not start. The restart
protection is active. If the mains plug is
inserted with the machine switched on, or if the
current supply is restored following an interruption,
the machine does not start up. Switch the machine
off and on again.
Use only genuine Metabo accessories. See page 4.
Use only accessories which fulfil the requirements
and specifications listed in these operating instruc-
tions.
8. Use
0
I
5
9. Cleaning
10. Troubleshooting
11. Accessories
0
I
8 989
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo W 8-100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo W 8-100 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info