599592

Metabo W 26-180 Manual

15
Zoom out
Zoom in
Previous page
1/116
Next page
ENGLISH en
15
See page 2.
1 "Quick"clamping nut *
2 Support flange
3Spindle
4 Spindle locking button
5 Electronic signal indicator*
6 Lock (to prevent the machine from being switched
on unintentionally, or for continuous operation)*
7 Trigger (
for switching on and off)
8 Button (to turn the main handle)*
9 Main handle
10 Additional handle / Additional handle with vibration
damping *
11 Safety guard
12 Clamping nut *
13 2-hole spanner *
14 Lever (to adjust safety guard without the use of
tools)
* depending on equipment/not in scope of delivery
If delivered without a mains plug, arrange for a
suitable mains plug to be connected by a
qualified electrician ONLY.
Before plugging in, check to see that the rated
mains voltage and mains frequency, as
specified on the rating label, match your power
supply.
Always use an extension cable with a minimum
diameter of 1.5 mm
2
. The extension cable must be
suitable for the machine power rating (see
Technical Specifications). If using a roll of cable,
always roll up the cable completely.
6.1 Attaching the additional handle
Always work with the additional handle
attached (10)! Manually screw in the
additional handle securely in the left, centre or right
threaded hole (depending on requirements).
6.2 Attaching the safety guard
(for work involving grinding wheels)
Prior to commissioning: Fit the
protective cover.
For reasons of safety, the safety guard (11)
should always be attached when roughing
work is performed.
For reasons of safety, the special parting
guard should always be attached before
parting work is performed (see chapter 11.
Accessories).
See illustration E on page 2.
- Push and hold the lever (14). Place the safety
guard (11) in the position indicated.
- Release the lever and turn the safety guard until
the lever engages.
- Push the lever and turn the safety guard until the
closed section is facing the operator.
- Make sure that the guard is seated securely: the
lever must engage and you should not be able to
turn the safety guard.
Use only accessories that
are covered by at least
3.4 mm by the safety guard.
6.3 Rotatable main handle (depending on
features)
Only work with the main handle (9) engaged.
See illustration B on page 2.
- Push in the button (8).
- The main handle (9) can now be turned 90° to both
sides and can be engaged.
- Make sure that it is securely positioned: the main
handle (9) must be engaged and it should not be
possible to move it.
6.4 Power supply
The mains sockets must be protected using time-
delay fuses or circuit breakers.
Machines with "X" in the model designation:
(with integrated, automatic restriction of the starting
current (soft start)). The mains sockets can also be
protected using fast-acting fuses or circuit breakers.
Disconnect the mains plug before changing
any accessories. The machine must be
switched off and the spindle at a standstill.
For reasons of safety, attach the parting guard
before performing parting work (see chapter
11. Accessories).
7.1 Locking the spindle
Press in the spindle locking button (4) only
when the spindle is stationary!
- Press in the spindle locking button (4) and turn the
spindle
(3) by hand until you feel the spindle locking
button engage.
7.2 Placing the grinding wheel in position
See illustration C on page 2.
- Fit the support flange (2) on the spindle. The
flange should not turn on the spindle when
properly attached.
- Position the grinding wheel on the support flange
(2) as shown in illustration C.
The grinding wheel must lay flat on the supporting
flange. The metal flange on the parting grinder
disc must lay flat on the support flange.
7.3 Securing/Releasing the "Quick"clamping
nut (depending on features)
Securing the "Quick"clamping nut (1):
5. Overview
6. Commissioning
7. Attaching the grinding wheel
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo W 26-180 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo W 26-180 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info