511040
17
Zoom out
Zoom in
Previous page
1/116
Next page
ENGLISH
17
ENG
Electronic signal indicator (10)
(SBE 1010 Plus)
Rapid flashing - restart protection
When power is restored after a power failure, the
still switched-on machine does not start for safety
reasons. Switch machine off, then on again.
Slow flashing - carbon brushes worn
The carbon brushes are almost completely worn.
If the brushes are completely worn, the machine
switches off automatically. Have the brushes
replaced by an authorized service centre.
Permanently lit - overload
In the event of prolonged overloading of the
machine, the power input is limited to prevent a
further inadmissible temperature rise of the motor.
Let machine cool down by letting it run at high
speed under no load.
f
Use only genuine Metabo accessories.
If you need accessories, check with your dealer.
For the dealer to select the correct accessory, he
needs to know the exact model designation of your
power tool.
See page 4.
AMetabox
B Angle Drilling and Screwdriving Attachment
C Flexible Shaft
D Rubber Backing Pad
E Linen-backed Sanding Discs
F Drill Stand
(drill clamp can be rotated by 360°.)
G Moulding & Drill Stand
(Column with toothed rack and guide groove)
H Machine Vice
I Steel-wire End Brush
J Steel-wire Cup Brush
K Steel-wire Wheel Brush
L
Fitting bit spring
For complete range of accessories, see
www.metabo.com or the main catalogue.
Repairs to power tools must be carried out by
qualified electricians ONLY!
Any Metabo power tool in need of repair can be
sent to one of the addresses listed on the page
before the last page.
Please attach a description of the fault to the
machine.
Metabo's packaging can be 100% recycled.
Worn out power tools and accessories contain
considerable amounts of valuable raw and plastic
materials, which can be recycled.
These instructions are printed on chlorine-free
bleached paper.
Only for EU countries: Never dispose of
power tools in your household waste! In
accordance with European Guideline
2002/96/EC on used electronic and electric
equipment and its implementation in national legal
systems, used power tools must be collected sepa-
rately and handed in for environmentally compat-
ible recycling.
Explanatory notes on the information on page 2.
Changes due to technological progress reserved.
P
1
= rated input
P
2
= rated output
n
1
*1 = no-load speed
n
2
*1 = load speed
ø max = max. solid drill diameter
S max = max. impact rate
b = drill chuck clamping capacity
G = spindle thread
H = spindle with hexagon socket
m=weight
D = spindle collar diameter
Vibration total value (vector sum of three
directions) determined in accordance with
EN 60745
a
h,ID
= Typical estimated acceleration
in the hand/arm area
(Impact drilling in concrete)
K
h,ID
= Uncertainty (vibration)
The vibration emission level given in this informa-
tion sheet has been measured in accordance with
a standardised test given in EN 60745 and may be
used to compare one tool with another. It may be
used for a preliminary assessment of exposure.
The declared vibration emission level represents
the main applications of the tool. However if the tool
is used for different applications, with different
accessories or poorly maintained, the vibration
emission may differ. This may significantly increase
the exposure level over the total working period.
12 Accessories
13 Repairs
14 Protection of the
Environment
15 Technical Specifications
17026951_0709 SB_Bauk.book Seite 17 Montag, 13. Juli 2009 1:54 13
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo UT 3000 E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo UT 3000 E in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6,08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info