595384
10
Zoom out
Zoom in
Previous page
1/72
Next page
ENGLISHen
10
Replacing the chuck:
Place chuck onto spindle (6) (a). Turn chuck lock (5)
in the direction indicated by the arrow (b) until chuck
slides fully onto the spindle. Then release the chuck
lock.
Check to see that the chuck is properly seated.
Note: To prevent the spindle from turning while
changing chucks, set the switch button (14) to
chiselling mode.
7.7 Tool change with SDS chuck
Before fitting, clean tool shank and apply
special grease (accessories order no.
6.31800)! Use only SDS-Plus tools.
Inserting the tool:
Turn the tool while inserting until it locks into place.
The tool is locked automatically.
Removing the tool:
Turn tool lock (3) in direction indicated by arrow (a)
and remove tool (b).
7.8 Tool change with keyless chuck
Use the keyless chuck when non-impact drilling in
metal, wood etc. and driving screws.
Chucking the tool
Turn sleeve (4) in the direction of "AUF, OPEN" (a).
Insert tool as deeply as possible (b) and turn sleeve
in the opposite direction, until the mechanical
resistance which can be felt is overcome. Caution!
The chuck is not yet fully tightened!
Keep turning the sleeve (it must "click" when
turning) until it cannot be turned any further - only
now is the tool securely clamped.
With a soft tool shank, retightening may be required
after a short period of operation.
Removing the tool:
Turn sleeve (4) in the direction of "AUF, OPEN", and
remove the tool.
Note: The grating sound which may be heard after
opening the drill chuck is functional and is stopped
by turning the sleeve in the opposite direction.
If the chuck is very securely tightened: Unplug.
Hold drill chuck using an open-end spanner at the
flats on its head, and turn the sleeve (4) vigourously
in the direction of "AUF, OPEN".
Only moderate pressure is required for hammer
drilling and chiselling. Applying a high degree of
pressure does not increase performance.
When drilling deep holes, remove the drill bit
periodically from the hole to remove dust.
Drill tiles and other brittle materials without impact.
Always keep the safety coupling (17) clean and
free from dust.
Always keep the spindle (6) clean and apply a light
coating of grease. (for information on special
grease, see Accessories section: order no.
6.31800)
Keyless chuck (1) cleaning:
After prolonged use, hold the chuck vertically, with
the opening facing down, and fully close it and open
it several times. The dust collected falls from the
opening. The application of cleaning spray to the
jaws and jaw openings at regular intervals is
recommended.
Ventilation slits:
Clean the ventilation slits on the machine
occasionally.
If the trigger (13) can not be depressed, check to
see that the direction of rotation selector switch (11)
is fully set to the R or L position.
Electronic signal indicator (10):
Rapid flashing - restart protection
When power is restored after a power failure, the
machine - which is still switched on - will not start for
safety reasons. To continue operation, switch the
tool off and then on again.
Slow flashing - carbon brushes worn
The carbon brushes are almost completely worn.
If the brushes are completely worn, the machine
switches off automatically. Have the brushes
replaced by an authorized service centre.
b
a
b
a
b
a
8. Tips and Tricks
9. Servicing
10. Troubleshooting
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo UHE 2450 Multi at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo UHE 2450 Multi in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info