816519
9
Zoom out
Zoom in
Previous page
1/76
Next page
ENGLISH en
9
Only send the battery pack if the housing is intact
and no fluid is leaking. Remove the battery pack
from the machine for sending. Prevent the contacts
from short-circuiting (e.g. by protecting them with
adhesive tape).
4.1 Reducing dust exposure:
WARNING - Some dust created by power
sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to
cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
- Lead from lead-based paints,
- crystalline silica from bricks and cement and other
masonry products, and
- arsenic and chromium from chemically treated
lumber.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well-
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designed to filter out microscopic
particles.
This also applies to dust from other materials, such
as some timber types (like oak or beech dust),
metals, asbestos. Other known diseases are e.g.
allergic reactions, respiratory diseases. Do not let
dust enter the body.
Observe the relevant guidelines and national
regulations for your material, staff, application and
place of application (e.g. occupational health and
safety regulations, disposal).
Collect the particles generated at the source, avoid
deposits in the surrounding area.
Use suitable accessories for special work. In this
way, fewer particles enter the environment in an
uncontrolled manner.
Use a suitable extraction unit.
Reduce dust exposure with the following measures:
- do not direct the escaping particles and the
exhaust air stream towards yourself or nearby
persons or towards dust deposits,
- use an extraction unit and/or an air purifier,
- ensure good ventilation of the workplace and keep
it clean using a vacuum cleaner. Sweeping or
blowing stirs up dust.
- Vacuum or wash protective clothing. Do not blow,
beat or brush protective gear.
See page 2.
1 Rotation selector switch
2Handle
3Trigger
4 Battery pack release button
5Belt hook *
6 Battery pack *
7 Capacity indicator button *
8 Capacity and signal indicator *
9 Setting wheel (select operating mode)
10 LED light
11 Depth stop
12 Screwdriver bit*
13 Bit holder
14 Spindle
15 Closure sleeve
16 Stop sleeve
17 Setting sleeve
18 Union sleeve
* depending on the model / features
a
6.1 Battery pack
Charge the battery pack (6) before use.
Recharge the battery pack if performance
diminishes.
Instructions on charging the battery pack can be
found in the operating instructions of the Metabo
charger.
In case of Li-Ion battery packs with capacity and
signal display (8) (equipment-specific):
- Press the button (7); the LEDs indicate the charge
(8) level.
- The battery pack is almost empty and must be
recharged if one LED is flashing.
Removing and inserting the battery pack
Removal: press the battery pack release button (4)
and pull the battery pack (6) forwards.
To insert: Slide the battery pack (6) in until it
engages.
6.2 Installation of belt hook
The belt hook (5) may be screwed into place on the
left or the right (see illustration, page 2).
7.1 Setting the direction of rotation,
engaging the transporting safety device
(switch-on lock)
Only activate the rotation selector switch (1)
when the motor has completely stopped.
See page 2:
R= Clockwise setting
L= Anti-clockwise setting
0= Centre position: with the transporting safety
device engaged (switch-on lock)
7.2 Selection operating mode, switch on / off
Set the required operating mode on the setting
wheel (9).
Note: When the motor is running, the spindle does
not start until the spindle is pushed in.
Manual mode
Switch on: press the trigger switch (3). Press
in the trigger to increase the rotational speed.
To switch off release the trigger switch.
Automatic mode
The tool starts automatically when the
5. Overview
6. Initial Operation
7. Use
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo TBS 18 LTX BL 5000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo TBS 18 LTX BL 5000 in the language / languages: All languages as an attachment in your email.

The manual is 5.47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info