Manual Metabo SXE 450 TURBOTEC (page 8 of 56) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

595431

Zoom out

Zoom in

1/56

ENGLISHen

7.1 Duo oscillating circuit setting (only with

SXE 450 TurboTec)

You can choose between two oscillating frequency

settings:

• Oscillating circuit high setting (6.2 mm): coarse

sanding with high material removal rate

• Oscillating circuit low setting (2.8 mm): fine

sanding, polishing

Changing oscillating circuit:

- Disconnect the mains plug!

- Press in the locking button (9) and hold in place.

- Rotate support plate (2) in a counter-clockwise

direction until you can hear it engage.

- Continue holding in the button.

- Continue turning the support plate half a

revolution to the next snap-in point.

- Release the locking button.

7.2 On/Off switch, continuous activation

To start the machine, press the trigger switch (8).

For continuous operation the trigger switch can be

locked using the lock button (7). To stop the

machine, press the trigger switch (8) again.

7.3 Setting oscillating frequency

When the TurboBoost switch (6) is switched

off, the oscillating speed can be set at the

setting wheel (5). This is also possible during

operation.

Recommended oscillating frequency settings:

Plastic materials. . . . . . . . . . . . . . . . . . . . . 1-2

Metal, Plexiglas

, old coats of paint. . . . . 3-4

Coarse and fine sanding, polishing, wood 5

The best way to determine the ideal setting is

through a practical trial.

7.4 TurboBoost switch

Actuate the TurboBoost switch (6) during operation

to switch on additional power reserves for maximum

material removal rate.

7.5 Dust extraction

To optimise the dust extraction performance, fit the

sanding disc such that the holes on the sanding disc

(1) are aligned to the support plate (2).

Own extraction system:

Fit the dust collection box (12) onto the exhaust

nozzle until it engages. To remove, press the button

(11) and pull off the dust collection box (12) to the

rear.

To optimise the extraction performance, empty the

dust collection box (12) in good time and clean the

filter (14).

External extraction system:

Connect a suitable extraction device.

Empty dust collection box (12).

- Open cleaning flap (13).

- Empty dust collection box (12).

- Remove fluted filter (14) and knock off dust stuck

to filter or remove with brush.

- When inserting, ensure that the fluted filter (14) is

inserted in the lateral guides.

The clean the machine regularly, frequently

and thoroughly. Vacuum clean the ventilation

slots on the motor or blow compressed air through

the ventilation slots. Hold the machine firmly at the

same time.

Replacing a worn support plate

Note:

If abrasive material (e.g. filled or painted

surfaces, etc.) is being sanded, the support plate

inevitably wears faster.

-Use the

hexagon spanner

(10) to unscrew the

fixing screw (15) on the support plate.

- Remove support plate (2).

- For replacement support plates, refer to the

Accessories chapter.

- Mount support plate (2) and rotate until it engages

on carrier disc.

- Insert locking screw (15) again and tighten.

Replacing support plate brake / braking ring

If the idling speed of the support plate increases in

course of time, the braking ring (16) is worn and

must be replaced.

Note:

If abrasive material (e.g. filled or painted

surfaces, etc.) is being sanded, the braking ring

inevitably wears faster.

-Use the

hexagon spanner

(10) to unscrew the

fixing screw (15) on the support plate.

- Remove support plate (2).

- Replace the old braking ring (16) with the new

braking ring (see Chapter on Accessories),

ensuring that the new braking ring is in the same

position as the old braking ring. Ensure that the

position of the marking on the braking ring is

correct.

- Mount support plate (2) and rotate until it engages

on carrier disc.

- Insert locking screw (15) again and tighten.

Do not press the device too firmly against the

surface being sanded. This does not improve, but

rather impairs, the sanding performance.

To optimise the extraction performance, empty the

dust collection box (12) in good time and clean the

fluted filter (14).english

Use a suitable sanding disc to achieve the best

possible work results: Removal of old paint layers =

P 40

Pre-sanding of wood = P 60, P 80

Finishing of wood = P 100, P 120

Sanding of veneers, sealing primer, filler, paint = P

180, P 240, P 320, P 400

7. Use 8. Cleaning, Maintenance

9. Tips and Tricks

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Metabo SXE 450 TURBOTEC in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,51 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Metabo SXE 450 TURBOTEC Manual

Product: