595427
10
Zoom out
Zoom in
Previous page
1/68
Next page
ENGLISHen
10
Always install an RCD with a maximum trip
current of 30 mA upstream.
6.1 Installation of sanding disc
Simple attachment and removal thanks to the
velcro-type fastening. Simply press on the sanding
disc so that the holes in the sanding disc (1) are
aligned with the support plate (2).
7.1 On/Off switch, continuous activation
Press the trigger switch (5) to switch on the
machine.
The trigger switch can be locked using the lock
button (7) for continuous operation. Press the
trigger switch (5) again to stop the machine.
7.2 Setting the oscillating frequency
Set the oscillating frequency on the adjustment
wheel (4). This can also be done during operation.
The best way to determine the ideal setting is
through a practical trial.
7.3 Dust extraction
To optimise the dust extraction performance, fit the
sanding disc (1) so that the holes on the sanding
disc are aligned to the support plate (2).
Note:
We recommend connecting a suitable
extraction device when sanding abrasive material
(e.g. plaster, etc.).
Own extraction units:
Fit dust bag (8) to the ejection nozzle (3). Pull the
dust bag (8) backwards to remove it.
Empty the dust bag (8) in good time to optimise dust
extraction.
Third-party extraction units:
Pull the dust bag (8) backwards.
Connect a suitable extraction device to the ejection
nozzle (3).
Emptying the dust bag:
Remove the closure band (9). Empty the dust bag
(8), clean with an extraction device if necessary.
Close the dust bag again with the closure band (9).
Clean the machine regularly. This includes
vacuum cleaning the ventilation louvres on the
motor.
Replacing a worn support plate
- Remove the locking screw (10) of the support
plate.
- Remove support plate (2).
- Refer to the Accessories chapter for replacement
support plates with velcro-type fastening.
- Mount support plate (2) and rotate until it engages
on carrier disc.
- Insert locking screw (10) again and tighten.
Clean the support plate as required (vacuum off
the dust). This increases the service life of the
velcro-type fastening.
Replacing a support plate brake / braking ring
If the idle speed of the support plate increases in
course of time, the braking ring (11) is worn and
must be replaced.
Note:
If abrasive material (e.g. gypsum, etc.) is
being sanded, the braking ring inevitably wears
faster.
- Remove the locking screw (10) of the support
plate.
- Remove support plate (2).
- Replace the old braking ring (11) with the new
braking ring (order no.: 344099810), ensuring
that the new braking ring is in the same position as
the old braking ring.
- Mount support plate (2) and rotate until it engages
on carrier disc.
- Insert locking screw (10) again and tighten.
Use only genuine Metabo accessories.
Note:
Metabo accessories are adapted to suit the
machine's velcro-type fastening. This increases the
service life of the velcro-type fastening.
Use only accessories which fulfil the requirements
and specifications listed in these operating
instructions.
See www.metabo.com or the catalogue for a
complete range of accessories.
Repairs to electrical tools must ONLY be
carried out by qualified electricians!
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. See
www.metabo.com for addresses.
You can download a list of spare parts from
www.metabo.com.
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Only for EU countries: never dispose of
power tools in your household waste! Used
power tools must be collected separately and
handed in for environmentally compatible recycling
in accordance with European Directive 2002/96/EC
on waste electrical and electronic equipment and its
implementation in national legal systems.
Explanatory notes on the specifications on page 3.
Changes due to technological progress reserved.
D =Diameter of support plate
P
1
=Rated input power
7. Use
8. Cleaning, Maintenance
9. Accessories
10. Repairs
11. Environmental Protection
12. Technical Specifications
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo SXE 3125 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo SXE 3125 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info