665589
10
Zoom out
Zoom in
Previous page
1/60
Next page
ENGLISHen
10
The electronic signal indicator (3) does not
light up when the machine is switched on:
The mains cable (7) is not connected properly to the
machine or mains socket.
Connect the machine properly.
Overload protection:
The electronic signal
indicator (3) lights red and the speed of the
machine drops to 4000 min
-1
(rpm) during
the grinding process:
The temperature in the machine is too high. The
pressure on the machine is too high for a longer
time.
Exert less pressure on the machine for a moment,
then the speed of the machine will increase again.
Overload protection:
The electronic signal
indicator (3) lights red and the speed of the
machine decreases slightly:
The pressure on the machine is too high for a short
time.
Exert less pressure on the machine, then the LED
indicator (3) automatically switches back to green.
Electronic safety shutdown:
The electronic
signal indicator (3) lights red and the
machine has stopped:
The machine is in safety mode due to the high
temperature.
Wait until the machine has cooled down and the
electronic signal indicator goes off.
The support plate brake does not work:
Work braking ring (13) or damaged spindle bearing.
Check the braking ring (13) and replace if required
(see chapter 8.). If the spindle bearing is defective,
have it replaced (see chapter 11.).
Use only genuine Metabo accessories.
Note:
Metabo accessories are adapted to suit the
machine's hook and loop-type fastening. This
increases the service life of the hook and loop-type
fastening.
Use only accessories which fulfil the requirements
and specifications listed in these operating
instructions.
See www.metabo.com or the catalogue for a
complete range of accessories.
Repairs to electrical tools must only be carried
out by qualified electricians!
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. See
www.metabo.com for addresses.
You can download a list of spare parts from
www.metabo.com.
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Only for EU countries: never dispose of
power tools in your household waste! Used
power tools must be collected separately and
handed in for environmentally compatible recycling
in accordance with European Directive 2002/96/EC
on waste electrical and electronic equipment and its
implementation in national legal systems.
Explanatory notes on the specifications on page 3.
Changes due to technological progress reserved.
D =Diameter of support plate
P
1
=Rated input power
n
0
=Idle speed
n
1
=Speed at rated load
S =Oscillating circuit diameter
m =Weight without mains cable
Measured values determined in conformity with
EN 60745.
~ AC Power
Machine in protection class I
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
standards).
Emission values
These values make it possible to assess the
emissions from the power tool and to compare
different power tools. The actual load may be higher
or lower depending on the operating conditions, the
condition of the power tool or the accessories.
Please allow for breaks and periods when the load
is lower for assessment purposes. Arrange
protective measures for the user e.g. organisational
measures based on the adjusted estimates.
Vibration total value
(vector sum of three directions)
determined in accordance with EN 60745:
a
h, DS
=Vibration emission value (surface
grinding)
K
h,DS
=Uncertainty (vibration)
Typical A-effective perceived sound levels
:
L
pA
=Sound-pressure level
L
WA
=Acoustic power level
K
pA
, K
WA
=Uncertainty
The noise level can exceed 80 dB(A) during
operation.
Wear ear protectors!
10. Accessories
11. Repairs
12. Environmental Protection
13. Technical Specifications
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo SXE 150-2.5 BL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo SXE 150-2.5 BL in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info