759250
10
Zoom out
Zoom in
Previous page
1/72
Next page
ENGLISHen
10
Use suitable accessories for special work. In this
way, fewer particles enter the environment in an
uncontrolled manner.
Use a suitable extraction unit.
Reduce dust exposure with the following measures:
- do not direct the escaping particles and the
exhaust air stream at yourself or nearby persons
or on dust deposits,
- use an extraction unit and/or air purifiers,
- ensure good ventilation of the workplace and keep
clean using a vacuum cleaner. Sweeping or
blowing stirs up dust.
- Vacuum or wash the protective clothing. Do not
blow, beat or brush.
See page 2.
1 Clamping lever for securing the saw blade
2 Saw blade support roller
3 Saw blade
4 Screw for adjusting the footplate
5 Footplate
6
Switch button
on the
chip blower
7 Adjustment lever for pendulum motion
8 Anti-splintering footplate insert
9Protective cap
10 Saw blade clamping fixture
11 Protective rod for preventing unintentional
contact with the saw blade
12 Setting wheel for speed adjustment
13 Trigger
14 Lock button for continuous activation
15
Handle
16 Hexagon spanner
17 Extractor connection piece
18 Curved support plate indicating preset cutting
angle
Before plugging in, check to see that the rated
mains voltage and mains frequency, as stated
on the rating label, match your power supply.
Never operate the machine without a saw
blade.
Australia: Always use a residual current device
(RCD) protected supply with a rated residual
current of 30 mA or less.
6.1 Fitting the anti-splintering footplate
insert
Danger of injury due to the sharp jigsaw blade.
Remove the saw blade
before fitting (8) the anti-
splintering footplate insert.
Turn the machine over so that the footplate faces
upwards. Insert the anti-splintering footplate from
the front,
ensuring the following:
The smooth side of the footplate faces upwards.
The slot is facing to the rear (towards the mains
cable).
If you wish to work with the protective plate attached
(see chapter Accessories 10.), fit the anti-splintering
footplate insert in the protective plate.
6.2 Inserting the saw blade
Danger of injury due to the sharp jigsaw blade.
After stopping work, the jigsaw blade may still
be hot. Wear protective gloves.
Use a saw blade that is suitable for the material
being sawn.
- Push the clamping lever (1) forwards up to the
stop and release (the clamping lever remains
open).
- Insert the saw blade (3) up to the stop. Ensure that
the saw teeth are facing forwards and the blade is
seated correctly in the groove on the saw blade
support roller (2).
- Push back the clamping lever (1) to its original
position (the saw blade is now clamped securely
in position).
6.3 Attaching / Removing the protective cap
Attachment: Push on the protective cap (9) from
the front until it engages
Removal: Grip both sides of the protective cap (9),
lift slightly, then pull forwards and remove.
6.4 Sawing with dust extraction
- Connect a suitable extraction device to the
extractor connection piece (17). Use a suction
hose with a 30 mm connector diameter.
- Attach the protective cap (9) for maximum
extraction efficiency.
- Switch off the chip blower (see chapter 7.1).
6.5 Sawing without dust extraction
- Work with the protective cap (9) removed
(see Removal chapter 6.3).
6.6 Diagonal cuts
Remove the protective cap (9), anti-splintering
footplate insert (8) and extraction hose. These parts
cannot be used for diagonal cuts.
- Slacken the screw (4).
- Slid the footplate (5) forwards slightly and turn.
- Then slide the footplate (5) forwards or backwards
and engage in one of the detents (the detents can
be viewed through the semicircular opening at the
rear of the footplate (5).) The preset angle is
indicated on the curved support plate (18) on the
footplate. Adjust to different angles using an angle
gage.
- Tighten the screw (4) again.
6.7 Sawing close to the wall
Remove the protective cap (9), anti-splintering
footplate insert (8), circular-cutting and parallel
guide. These parts cannot be used when sawing
close to the wall.
- Slacken the screw (4) until the footplate (5) can be
raised slightly.
- Raise the footplate (5) slightly and slide
backwards up to the stop.
5. Overview
6. Commissioning
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo STEB 70 Quick at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo STEB 70 Quick in the language / languages: All languages as an attachment in your email.

The manual is 3,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info