658497
15
Zoom out
Zoom in
Previous page
1/68
Next page
ENGLISH en
15
- Caution! The tool is not yet fully tightened!
Keep turning the sleeve (it must "click" when
turning) until it cannot be turned any further - only
now is the tool safely clamped.
With a soft tool shank, retightening may be required
after a short period of operation.
8.10 Tool change, geared chuck (4)
Fig. K
8.11 Unscrew the chuck (when driving screws
without the chuck or for use with attach-
ments)
Fig. L, M, or N
Note for Fig. M, N:
Release by tapping lightly with a
rubber hammer, as shown, and unscrew.
Note:
If a bit clamping bush (order no. 6.31281) is
attached, the screwdriver bit inserted in the
hexagon socket of the spindle is held in place.
Keyless chuck cleaning:
After prolonged use hold the chuck vertically, with
the opening facing down, and fully open and close it
several times. The dust collected falls from the
opening. The application of cleaning spray to the
jaws and jaw openings at regular intervals is recom-
mended.
Electronic signal display (10):
Rapid flashing - restart protection
(SBEV 1300-2, SBEV 1300-2 S, SBEV 1100-2 S,
SBE 1000-2)
When power is restored after a power failure, the
machine - which is still switched on - will not start for
safety reasons. Switch machine on and off again.
Slow flashing - carbon brushes worn
(SBEV 1300-2, SBEV 1300-2 S, SBEV 1100-2 S)
The carbon brushes are almost completely worn. If
the brushes are completely worn, the machine
switches off automatically. Have the brushes
replaced by an authorized service centre.
Permanently lit - overload
(SBEV 1300-2, SBEV 1300-2 S, SBEV 1100-2 S)
If the machine is subject to long periods of contin-
uous overloading, the power input of the machine is
limited. This prevents the further unauthorized
heating of the motor.
Run the machine in idling until it cools down and the
electronic signal display switches off.
Use only genuine Metabo accessories.
Use only accessories which fulfil the requirements
and specifications listed in these operating instruc-
tions.
Fit accessories securely. Secure the machine if it is
operated in a bracket. Loss of control can cause
personal injury.
For a complete range of accessories, see
www.metabo.com or the main catalogue.
Repairs to electrical tools must be carried out by
qualified electricians ONLY!
If you have Metabo electrical tools that require
repairs, please contact your Metabo service centre.
For addresses see www.metabo.com.
You can download spare parts lists from
www.metabo.com.
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Only for EU countries: Never dispose of
power tools in your household waste! In
accordance with European Guideline 2002/
96/EC on used electronic and electric equipment
and its implementation in national legal systems,
used power tools must be collected separately and
handed in for environmentally compatible recycling.
Fig. O.
We reserve the right to make technical
improvements.
P
1
=Rated input
P
2
=Power output
n
1
* =No-load speed
n
2
*=Load speed
max. dia. =Max. solid drill diameter
s max =Max. impact rate
b =Chuck capacity
G=Spindle thread
H =Spindle with hexagon socket
m=Weight
D =D=Collar diameter
Measured values determined in conformity with
EN 60745.
Machine in protection class II
~ Alternating current
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
standards).
* Energy-rich, high-frequency interference can cause
fluctuations in speed. The fluctuations disappear,
however, as soon as the interference fades away.
Emission values
Using these values, you can estimate the emis-
sions from this power tool and compare these with
the values emitted by other power tools. The actual
values may be higher or lower, depending on the
particular application and the condition of the tool or
power tool. In estimating the values, you should also
include work breaks and periods of low use. Based
on the estimated emission values, specify protective
measures for the user - for example, any organisa-
tional steps that must be put in place.
Vibration total value (vector sum of three directions)
determined in accordance with EN 60745:
9. Cleaning, Maintenance
10. Troubleshooting
11. Accessories
12. Repairs
13. Environmental Protection
14. Technical Specifications
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo SBE 850-2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo SBE 850-2 in the language / languages: All languages as an attachment in your email.

The manual is 12,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info