Manual Metabo SBE 760 (page 10 of 60) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

511042

Zoom out

Zoom in

1/60

ENGLISHen

To ensure that the drill chuck is securely fitted:

After initial drilling (clockwise), use a

screwdriver to firmly tighten the safety screw inside

the drill chuck (if applicable / model-specific).

Caution left-handed thread !

(see Section 7.9.)

6.1 Assembly of additional handle (2)

For safety reasons, always use the additional

handle supplied.

Open the clamping ring by turning the additional

handle (2) counter-clockwise. Push the additional

handle onto the collar of the machine. Slide the

additional handle far enough forward so that it can

be turned. At the desired angle, pull it back and

tighten firmly.

7.1 Adjusting the Depth Stop

Loosen the additional handle (2). Set depth stop (5)

to the desired drilling depth and retighten additional

handle.

7.2 Setting direction of rotation,

transport lock (switch-on lock)

Do not activate the rotation selector switch (8)

unless the motor has completely stopped.

See page 2.

R = Clockwise setting

L = Counter-clockwise setting

0 = Central position: transport lock setting

(switch-on lock)

The drill chuck must be firmly screwed onto

the spindle and the safety screw inside the drill

chuck (if applicable / model-specific) must be firmly

tightened with a screwdriver. (Caution, left-handed

thread !) If rotated counterclockwise (e.g. when

screwing) it could otherwise become loose.

7.3 Selecting a gear

Select the desired gear by turning the

thumbwheel (1).

Change speed only when the machine

is in the process of running down

(briefly switch it on and off).

1st gear (low speed, high torque)

e.g. for screwdriving, drilling

2nd gear (high speed) e.g. for drilling

7.4 Switching Between Normal Drilling/

Impact Drilling

Select the desired operating mode by pushing the

sliding switch (6).

Drilling

Impact drilling

Work with high speed settings when impact drilling.

Impact drilling and normal drilling

only in a clockwise direction.

7.5 Preselect speed

Use the setting wheel (5) to preselect the maximum

speed. See page 4 for recommended drilling

speeds.

7.6 Switching on/off, changing speed

Switching on, speed: press the trigger (10).

SBE 760: The speed can be changed by

pressing in the trigger.

Release the trigger to switch off.

Continuous activation: While pressing on the

trigger (10), press in the locking button (9) and

then release the trigger. To switch off, press and

release the trigger (10) again.

In continuous operation, the machine

continues running if it is forced out of your

hands. Therefore, always hold the machine with

both hands using the handles provided, stand in

a safe position and concentrate.

7.7 Tool change with

(4)

chuck

See illustrations A on page 2.

Opening the drill chuck:

Grip the retaining ring and, using the other hand,

rotate the sleeve in the direction of the arrow -1-.

The grating sound (depending on function) which

may be heard after opening the drill chuck is

stopped by turning the sleeve in the opposite

direction.

If the chuck is very tightly secured,

disconnect from

mains. Hold the chuck using an open-end spanner

at the flats on its head, and turn the sleeve

vigourously in the direction of the arrow -1-.

Clamping the tool

- Insert the tool -2- as far as it will go.

- Grip the retaining ring and, using the other hand,

rotate the sleeve in the direction of the arrow -3-

until the mechanical resistance which can be felt is

overcome.

- Caution! The tool is not yet fully clamped!

Keep turning the sleeve (it must "click" when

turning) until it cannot be turned any further - only

now is the tool securely clamped.

In the case of a soft tool shank, retightening may be

required after a short period of drilling.

7.8 Tool change with a geared chuck (3)

See illustrations B on page 2.

Opening the chuck: Opening a geared chuck with

the chuck key -1-.

Clamping the tool: Insert tool -2- as far as it will go

and tighten equally in all 3 bores using the chuck

key -3-.

7.9 Unscrew the chuck (when driving screws

without the chuck or for use with attach-

ments)

See illustrations A, B, on page 3.

Note for Fig. A, B:

Release by tapping lightly with a

rubber hammer, as shown, and unscrew.

7. Use

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Metabo SBE 760 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,44 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Metabo SBE 760 Manual

Product: