511032
15
Zoom out
Zoom in
Previous page
1/116
Next page
ENGLISH
15
ENG
(a) firmly and turn sleeve (b) in the opposite
direction.
8.8 Tool change with Futuro Plus keyless
chuck (2)
Insert tool. Grip the retaining ring (a) firmly and,
with the other hand, turn sleeve (b) towards GRIP,
ZU", until the mechanical resistance which can be
felt is overcome.
Caution! The chuck is not yet fully tightened!
Keep turning
(there is a clicking" sound while
turning)
, until further turning is no longer possible -
only now
is the tool
securely
tightened.
When using soft bit shanks, it may be necessary to
retighten the chuck after a short period of
operation.
Opening the drill chuck:
Grip the retaining ring (a) firmly and, with the other
hand, turn the sleeve (b) towards AUF, RELEASE".
Note:
The ratchet sound which can possibly be
heard after opening the drill chuck, is functional and
is switched off by a reverse rotation of the sleeve.
If the tool is fitted very tight:
Unplug. Hold drill chuck with an open end spanner
at the jaw opening and turn sleeve (b) firmly
towards "AUF, RELEASE".
8.9 Tool change with geared chuck (1)
Fitting the tool:
Insert the tool and tighten evenly with chuck key in
all three 3 holes.
Removing the tool:
Open the geared chuck with the chuck key and
remove tool.
8.10 Contact mode
(SBE 850 Contact)
To enable the contact mode press button (8).
If required, e.g. for drilling into steel girders or
steel-reinforced concrete walls, the contact mode
can be disabled by pressing the switch button (8).
The contact mode indicator (7) shows the current
setting:
Green:contact mode enabled.
Red: machine has switched off because contact
was made with conductive, earthed
material or a live supply cable.
Pull machine back and bit out of the hole
immediately. Have possible damage
properly repaired.
Off: contact mode disabled.
8.11 Pulse function
(SBE 85, SBE 850 Impuls)
Adjust via the thumbwheel (9).
Pulse function constantly switched On
+ Pulse function Off (for drilling)
Recommended settings for screwdriving, for
example, into wood (soft screwdriving)::
8.12 Torque limiter
(SBE 85, SBE 850 Impuls)
Upon attainment of the preselected torque the
motor comes to a standstill. Adjust via the
thumbwheel (9). (positions 1 - 6).
1 Upon attainment of a low torque the motor
comes to a standstill.
a
b
3x
ø
4,0
B2
4,5
B3
5,0
C3
6,0
C4
8,0
D5
17026951_0709 SB_Bauk.book Seite 15 Montag, 13. Juli 2009 1:54 13
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo SB 660 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo SB 660 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6,08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info