585249
15
Zoom out
Zoom in
Previous page
1/68
Next page
15
ENGLISH
Cleaning the impeller
1. Undo Phillips screws on pump base plate.
If necessary push back the two clips on
pump base plate using a screwdriver.
2. Remove base plate.
3. Clean impeller.
4. Mount base plate, fasten screws and if
necessary secure with the clips.
6.2 Pump storage
A Caution!
Frost damages the pump and accesso-
ries as both always contain water!
If there is a danger of frost disassemble
pump and accessories and store in frost-
free conditions.
ADanger!
Prior to all servicing:
Unplug.
7.1 Troubleshooting guide
Pump does not run:
No mains voltage.
Check cables, plug, outlet and mains
fuse.
Mains voltage too low.
Use an extension cable with sufficient
conductor diameter.
Motor overheated; motor protection relay
tripped.
Eliminate the cause of overheating
(pump blocked by foreign objects?).
After cooling the pump will switch ON
again.
Float switch does not switch pump ON
when water level rises.
Make sure the float switch can move
unrestrictedly.
If, despite sufficient mobility of the float
switch, the pump does not switch ON:
send the pump to the service centre in
your country.
Motor hums, but does not start:
Pump blocked by foreign objects.
Clean impeller.
Pump runs, but does not pump properly:
Delivery head too high.
Observe max delivery head (see 'Tech-
nical Specifications').
Discharge hose kinked.
Straighten discharge hose.
Discharge hose leaky.
Seal discharge hose; tighten screw fit-
tings.
Pump runs very noisily:
Pump is sucking air.
Ensure there is a sufficient water sup-
ply.
Foreign objects are present (clean
pump).
Manual mode has been set (shallow
water suctioning).
Hold pump at an angle when submerg-
ing.
Pump runs continuously:
Float switch does not reach cut-out posi-
tion.
Make sure the float switch can move
unrestrictedly.
ADanger!
Repair of power tools must be carried out by
qualified electricians only!
Power tools in need of repair can be sent to
the service centre in your country. Refer to
spare parts list for address.
Please attach a description of the fault to the
power tool.
Power tools do not belong in the
household rubbish. According to
European
Directive 2002/96/EC on waste
electrical and electronic
equipment, electrical waste must
be collected separately and taken
to an environmentally friendly recycling
facility.
Contact your local council for information on
disposal of the used tool.
All packaging materials are recyclable.
7. Troubleshooting
8. Repairs
9. Disposal
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo PS18000SN at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo PS18000SN in the language / languages: English, German, Dutch, Danish, French, Swedish as an attachment in your email.

The manual is 0,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info