595156
23
Zoom out
Zoom in
Previous page
1/76
Next page
23
D
D: When working with the router, the knob must always
be screwed tight.
Smaller workpieces must be firmly secured to
prevent them from moving around when being
worked on with the router (e.g. use screw clamps).
D: Pendant les travaux avec la défonceuse, le
pommeau doit toujours être bien serré. Fixer les
petites pièces à usiner de telle sorte qu’elles ne
puissent pas se desserrer pendant le travail avec la
défonceuse (par ex. serrer avec des serre-joints).
D: Der Knaufgriff muß bei Arbeiten mit der Oberfräse
immer fest angezogen sein.
Kleinere Werkstücke müssen so gesichert werden,
daß sie sich beim Arbeiten mit der Oberfräse nicht
lösen (z.B. mit Schraubzwingen festklemmen).
D: De knopgreep moet bij het werken met de
bovenfrees altijd stevig aangedraaid zijn.
Kleine werkstukken moeten zo bevestigd worden dat
ze bij het bewerken met de bovenfrees niet losraken
(bijv. met lijmklemmen).
D: Prima d'avviare la fresatrice, controllare sempre che il
pomello sia stretto a fondo. È bene fissare pezzi di
dimensioni ridotte, che devono essere lavorati, in modo
da evitarne il distacco durante il funzionamento della
fresatrice (bloccaggio per es. con morsetti da falegname).
D: Cuando se trabaje con la fresa superior, observar
que la empuñadura de bola esté bien apretada.
Cuando se mecanicen piezas de pequeño tamaño,
fijarlas bien (p.ej. con un sargento) para evitar que se
suelten al trabajar con la fresa superior.
D: O punho tem de estar sempre bem apertado durante
o trabalho com a tupia.
Pequenas peças a trabalhar deverão ser fixadas de
modo a não se soltarem durante o trabalho com a
tupia (p.ex. fixar com grampos).
D: Under arbetet med överfräsmaskinen måste knoppen
alltid vara ordentligt åtdragen.
Mindre arbetsstycken måste säkras på så sätt att de
inte lossnar under arbetet med överfräsmaskinen
(fastkläms t ex med skruvtvingar).
D: Nuppikahvan on oltava kiristettynä käytettäessä
yläjyrsintä.
Pienemmät työkappaleet pitää varmistaa, että ne
eivät irtaudu työstön aikana (kiinnitä ne
esim.ruuvipuristimella)
D: Innstillingsknappen må under arbeid med overfresen
alltid være fast tiltrukket.
Små arbeidsstykker må være sikret slik at de ikke
løsner under arbeid med overfresen. (f.eks
fastspenning med skrutvinge)
D: Indstillingsknappen skal altid være strammet, mens
De arbejder med overfræseren.
Små arbejdsstykker skal være således sikret, at de
ikke kan løsne sig, mens der arbejdes med
overfræseren (f.eks. fastspænding med skruetvinger).
D: W czasie użytkowania frezarki górnowrzecionowej gałka uchwytu
powinna być zawsze silnie dokręcona. Mniejsze przedmioty obrabiane
należy zabezpieczyć w taki sposób, aby nie uległy zwolnieniu w czasie
pracy z wykorzystaniem frezarki górnowrzecionowej (np.
unieruchomić przy pomocy zwornic stolarskich).
D: A felsőmaróval történő munkavégzés közben a
fogantyúgombnak mindig erősen meghúzva kell
lenni. Kisebb munkadarabokat úgy kell rögzíteni,
hogy a felsőmaróval végzett munka során ne
tudjanak meglazulni (pl. csavaros szorítóval befogni).
D: Η σφαιρική λαβή πρέπει κατά την εκτέλεση
εργασιών µε το ρούτερ να είναι καλά σφιγµένη. Μικρά
προσ κατεργασία τεµάχια πρέπει να είναι ασφαλισµένα
(π.χ. µε νταβίδι) έτσι, ώστε να µη λασκάρουν κατά την
εκτέλεση εργασιών µε το ρούτερ.
OfE_1229_Signal_0112_Teil1.qxp:OfE_1229_Signal_0508_Teil1.qxp 27.02.2013 16:57 Uhr Se
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo OF E 1229 SIGNAL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo OF E 1229 SIGNAL in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info