Manual Metabo Multi 310G (page 28 of 64) (English, German, Dutch, Danish)

451464

Zoom out

Zoom in

1/64

ENGLISH

5. Loosen arbor bolt (87) with spanner

(L.H. thread!).

6. Remove outer blade flange, saw

blade and inner blade flange from

the saw spindle.

7. Clean clamping surfaces of outer

blade flange and saw blade.



Danger!

Do not use cleaning agents

(e.g. to remove resin residue) that

could corrode the light metal compo-

nents of the saw; the stability of the

saw would be adversely affected.

8. Put on a fresh saw blade (observe

direction of rotation!).



Danger!

Use only suitable saw blades

(see "Technical Specifications") –

when using unsuitable or damaged

blades parts could be explosive-like

hurled from it by centrifugal force.

Do not use:

− saw blades made of high speed

steel (HS);

− saw blades with visible damage;

− cut-off wheel blades.



Danger!

− Mount saw blade only using

genuine parts.

− Do not use loose-fitting reducing

rings; the saw blade could work

loose.

− Saw blades have to be mounted

in such way that they do not

wobble or run out of balance, and

can not work loose during opera-

tion.

9. Put on the outer blade flange.

10. Turn in the arbor bolt (left-hand

thread!) and tighten fingertight

only.



Danger!

− Do not extend arbor bolt tighte-

ning wrench.

− Do not tighten arbor bolt by hit-

ting the Allen key.

− After tightening the arbor bolt do

not forget to remove the retention

pin!

11. Replace table insert (84) flush with

the table top.

12. Install blade guard (85).

10.3 Care and maintenance



Danger!

The checks and procedures

described here are meant to help ope-

rate the machine safely! Should there

be faults evident on any of these

components, the machine must not

be used until these faults have been

remedied in a workmanlike manner.

Before starting any work

1. Check power supply cable for dam-

age, if necessary have replaced by

a qualified electrician.

2. Remove sawdust and chips.

3. Check cutter knives for:

− tight seat

− sharpness

− general condition

(no notches etc.)

4. Check the thicknesser’s anti-kick-

back lock:

− mobility of anti-kickback fingers

(must fall down by their own

weight)

− points of anti-kickback fingers

(not rounded)

5. Check circular saw:

− Distance saw blade – riving knife

OK? (3 – 8 mm)

− Riving knife and blade guard

undamaged?

6. Check spindle moulder:

− Cutter guard undamaged?

Weekly:

1. Remove chips and dust with dust

collectoror brush from:

− thicknesser bed spindles;

− height setting mechanism of the

cutter spindle;

− height setting mechanism of the

circular saw;

− adjustment elements of the circu-

lar saw;

− telescopic type ball bearing trav-

eller and track of the sliding car-

riage.



Caution!

Do not spray care and mainte-

nance spray on flat belts and pulleys

– this will cause the flat belt to slip.

2. Apply a light coat of anti-seize com-

pound to infeed table, outfeed table

and thicknesser bed.

10.4 Machine Storage



Danger!

Store machine so that

− it can not be started by unauthori-

zed persons and

− nobody can get injured while the

machine is switched off.



Caution!

Do not store machine unpro-

tected outdoors or in damp environ-

ment.

For special tasks the following accesso-

ries are available at your specialized

dealer – see back cover for illustrations:

A Drilling and Morticing Attachment

for drilling mortices of max. 100 mm

depth and max. 100 mm long.

B Sliding Carriage Side Extension

required to work wide stock.

C Stock Stop

required for repetitive cut-off work.

D Tenoning Table

required for unproblematic tenon-

ing.

E Curved Moulding Stop

required for the exact guiding of

curved stock.

F Wheel Set

for convenient relocation of the

combination machine.

G HS Cutter Knives

310x20x2.5

for extended edge life. Resharpen-

able.

H TCT Saw Blade

250x3.2/2.2x30 24 ATB

for rip and crosscuts in grown tim-

ber and particle board.

I TCT Saw Blade

250x3.2/2.2x30 48 UAT

for rip and cross cuts in panels,

plastics, aluminium and high-quality

veneered sheets.

J TCT Saw Blade

250x3.2/2.2x30 60 combination

ATB

General purpose saw blade for

plastics and non-ferrous metals.

K TCT Saw Blade

250x3.2/2.2x30 80 trapezoidal flat

teeth

General purpose saw blade for

plastics and non-ferrous metals.

L Ball Transfer Stand

for exact guiding of long stock.

Used with either swivel ball or roller

head.

M WAXILIT Anti-seize Compound

improves stock gliding quality on

the planing beds.

N Care and Maintenance Spray

to remove resin residue and for pre-

serving the metal surfaces.



Danger!

Repairs to power tools must be

carried out by qualified electricians

only!

Power tools in need of repair can be sent

to the service centre of your country.

Refer to the spare parts list for the

address.

11. Available Accessories

12. Repairs

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Metabo Multi 310G in the language / languages: English, German, Dutch, Danish as an attachment in your email.

The manual is 4,67 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Metabo Multi 310G Manual

Product: