451463

Metabo Multi 260S Manual

20
Zoom out
Zoom in
Previous page
1/64
Next page
20
ENGLISH
Cutting hazard, even with the
cutting tool at standstill!
Wear gloves when changing cutting
tools.
Risk of kickback (workpiece is
caught by the saw blade and thrown
against the operator):
Always work with a properly set riving
knife.
Do not jam workpieces.
Cut thin or thin-walled workpieces only
with fine-toothed saw blades. Always
use sharp saw blades.
If in doubt, check workpiece for inclusion
of foreign matter (e.g. nails or screws).
Drawing-in/trapping hazard!
Ensure that no parts of the body or cloth-
ing ca be caught and drawn in by rotat-
ing components (no neckties, no loose-
fitting clothes; contain long hair with hair-
net).
Hazard generated by insuffi-
cient personal protection gear!
Wear hearing protection.
Wear safety glasses.
Wear dust mask if work generates dust.
Wear suitable work clothes. When work-
ing outdoors wearing of non-slip shoes is
recommended.
Risk of injury by inhaling wood
dust:
Dust of certain timber species (e.g. oak,
beech, ash) can cause cancer when
inhaled: Always use a dust collector. The
dust collector must meet the following
requirements:
− fitting the outer diameter of the suc-
tion port;
− air volume ≥ 550 m
3
/h;
− vacuum at suction port of machine
≥ 740 Pa;
− air speed at suction port of machine
≥ 20 m/s.
Hazard generated by modifica-
tion of the machine or use of
parts not tested and approved
by the equipment manufactu-
rer!
Assemble electric tool in strict accord-
ance with these instructions.
Use only parts approved by the equip-
ment manufacturer.
Do not make changes to any of the
parts.
Use only cutting tools according to
EN 847-1.
Use only matching saw blades and riving
knives.
Hazard generated by electric
tool defects!
Keep electric tool and accessories in
good repair. Observe the maintenance
instructions.
Check electric tool for possible damage
before any use: Before operating the
electric tool all safety devices, protection
devices or slightly damaged parts must
be inspected for proper functioning as
specified. Check to see that all moving
parts work properly and do not jam. All
parts must be correctly installed and
meet all conditions necessary for the
proper operation of the electric tool.
Damaged protection devices or parts
must be repaired or replaced by an qual-
ified specialist. Have damaged switches
replaced by a service centre. Do not
operate electric tool if the switch can not
be turned ON or OFF.
Keep handles free of oil and grease.
2.3 Symbols used through-
out these instructions
Danger!
Indicates risk of personal
injury or severe material
damage.
Risk of electric shock!
Risk of personal injury by elec-
tric shock.
Danger! Drawing-in/trapping
hazard!
Risk of personal injury by body
parts or clothing being drawn
into the rotating saw blade.
Caution!
Risk of material damage
Note:
Supplementary information
• One machine – four operating
modes:
− surface planer
− thicknesser
− circular saw
− spindle moulder
• Wide range of accessories.
• Latest technology for perfect per-
formance.
4.1 Machine installation
1. Transport combination machine on
the pallet to a suitable location:
− space required:
min. 3m x 4m
Depending on workpiece dimen-
sions more space may be
required.
− sufficient load bearing capacity
− level
− even
− dry
− non-slip.
2. Remove packing and enclosed parts
– do not yet remove the transport
brace inside the combination
machine!
3. Unscrew and remove the metal
clamps holding the combination
machine on the pallet.
4. Extend transport handle (1) fully.
5. Hold combination machine with sev-
eral persons at the transport handle
and the opposite table edge (2) and
lift it off the pallet.
Caution!
Lift machine only at both
marked spots (1) and (2) . Other com-
ponents are not designed for the ten-
sile load by the machine weight.
6. Open the access door.
7. Loosen lock lever (3) and lift motor
up.
8. While the motor is lifted up tighten
the lock lever.
9. Remove transport brace from under
the motor.
10. Close access door.
4.2 Wheel installation
1. Lift combination machine on one
side with the transport handle (1)
and place a wooden block under the
lifted side of the combination
machine.
Danger!
As long as the machine is kept
in this tilted position, it must be kept
from falling over by another person!
2. Put plastic protection covers over
both lifted feet of the machine.
3. Special Product Features
4. Transportation and
Installation
1
2
3
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo Multi 260S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo Multi 260S in the language / languages: English, German, Dutch, Danish as an attachment in your email.

The manual is 3,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info