658074
12
Zoom out
Zoom in
Previous page
1/39
Next page
12
ENGLISH
For shielded gas welding it must be
ensured that the shielding gas cover is
not blown away by air draft.
For machine performance see "Techni-
cal Specifications".
Any other use is not as specified and
prohibited.
The manufacturer does not assume any
liability for damage caused by unspeci-
fied use.
2.2 Symbols Used
Danger!
Disregard of the following
warnings could cause
serious personal injury or
material damage.
Read operating instruc-
tions before initial opera-
tion
2-step mode
4-step mode
Spot welding
Gasless and currentless
wire thread-up not applica-
ble for: MIG MAG 165 SP
MIG MAG 150/20 XT
Wire feed speed
Welding current coarse set-
ting (voltage)
Welding current fine setting
(voltage)
Supply voltage
Welding machine suitable
for welding in environ-
ments with an increased
electrical hazard.
Excess temperature
Information on the name plate:
3.1 Control Panel
3.2 MIG/MAG 150/20 XT
3.3 MIG/MAG 165 SP
2
345
7
8
1
6
1 Manufacturer
2 Machine designation
3 Serial number
4 Standard information – This
machine meets the requirements
of the standards mentioned
5 CE mark – This machine con-
forms to EC directives as per
declaration of conformity
6 Waste disposal symbol – the
machine can be disposed of
through the manufacturer
7 Electrical performance data
8 Date of manufacture
3. Operating Elements
9 Operating mode selector
switch
To set the operating mode.
10 LED overload (yellow)
Indicates overloads.
11 LED power (green)
Indicates the welding
machine's readiness for opera-
tion.
12 Wire feed setting knob
For setting the wire feed speed.
Setting range: approx. 0 to 20
m/min
(On the MIG/MAG 150/20 XT
the wire feed speed depends
on the set welding step as
well).
9101112
13
13 Weld time setting knob
For setting the weld time in
spot weld mode.
Setting range: approx. 0 to 15 s
14 Welding gun
(not detachable)
15 Earth cable (cross
section = 16 mm
2
)
16 Main switch
Position I: machine turned ON
Position 0: machine turned
OFF
17 Welding step selector switch
Switches the welding current
(voltage) in six steps.
18 Connector for welding gun
Accepts all commercially avail-
able welding guns (Euro con-
nector KZ-2).
15
14
16
17
19
18
20
21
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo MIG MAG 150-20 XT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo MIG MAG 150-20 XT in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 4,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info