600608
14
Zoom out
Zoom in
Previous page
1/104
Next page
ENGLISHen
14
The diamond cut-off wheels continue running after
the machine has been switched off.
Always wear protective goggles, dust mask, gloves,
ear protectors and sturdy shoes when working with
this tool.
Damaged, eccentric or vibrating tools must not be
used.
Avoid damage to gas or water pipes, electrical
cables and load-bearing walls (static).
Pull the plug out of the socket before making any
adjustments, converting or servicing the machine.
A damaged or cracked side handle must be
replaced. Never operate a machine with a defective
side handle.
A damaged or cracked safety guard must be
replaced. Never operate a machine with a defective
safety guard.
Do not switch on the machine if tool parts or guard
devices are missing or defective.
Reduce dust exposure:
Some of the dust created using this power tool
may contain chemicals known to cause
cancer, allergic reaction, respiratory disease, birth
defects or other reproductive harm. Some
examples of these chemicals are: Lead from lead-
based paints, crystalline silica from bricks and
cement and other masonry products, arsenic and
chromium from chemically-treated lumber, hard
wood like oak or beech, metals, asbestos.
The risk from exposure to such substances will
depend on how long you or bystanders are being
exposed.
Do not let particles enter the body.
To reduce your exposure to these substances: work
in a well ventilated area, and work with approved
safety equipment, such as dust masks that are
specially designed to filter out microscopic
particles.
Observe the relevant guidelines for your material,
staff, application and place of application (e.g.
occupational health and safety regulations,
disposal).
Collect the generated particles at the source, avoid
deposits in the surrounding area.
Use suitable accessories for special work. In this
way, fewer particles enter the environment in an
uncontrolled manner.
Use a suitable extraction unit.
Reduce dust exposure with the following measures:
- Do not direct the escaping particles and the
exhaust air stream at yourself or nearby persons
or on dust deposits.
- Use an extraction unit and/or air purifiers.
- Ensure good ventilation of the workplace and
keep clean using a vacuum cleaner. Sweeping or
blowing stirs up dust.
- Vacuum or wash the protective clothing. Do not
blow, beat or brush.
See page 2.
1Scale for depth of cut
2 Cross handled screw for setting the cutting
depth
3 Side handle
4Hex screw (guard)
5 Main handle
6 Aperture for the extraction unit
7 Electronic signal indicator
8Hex screw (guard)
9 Triangular marking (acts as cut indicator)
10 Safety cover
11 Sheath
12 Guide shoe
13 Locking button
14 Screw (for adjusting the position of the side
handle)
15 Slide switch (for switching on/off)
16 Support flange
17 Spacer rings
Before plugging in, check that the rated mains
voltage and mains frequency, as stated on the
type plate match your power supply.
Always install an RCD with a maximum trip
current of 30 mA upstream.
Mains connection: The wall chaser has an
electronic initial current limitation. It is sufficient for
the socket to which the machine is connected is
secured with a circuit-breaker of type H or a fast-
acting fuse.
Switch off the machine. Disconnect the mains
plug!
Caution! Never press the locking button (13)
when the machine is running (nor when it is
slowing down)!
See page 2.
- Undo the hex screw (4).
- Undo the hex screw (8) and set the guard (10) and
guide shoe (12) in such a way – see the second
image on page 2 – that you have free access to the
diamond cut-off wheel.
- Press the locking button (13), (with the other
hand) rotate the front diamond cut-off wheel
slowly until the locking button engages perceptibly
and
- with the locking button (13) pushed undo the
sheath (11) with the supplied two hole wrench.
5. Overview
6. Commissioning
7. Groove width
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo MFE 30 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo MFE 30 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info