625661
20
Zoom out
Zoom in
Previous page
1/128
Next page
20
ENGLISH
ENG
If it is necessary to clean the machine's oil channel,
unscrew the fixing screw on the cover (11) and
take off the cover.
Transporting the chainsaw
(after use): mount the contact protection (delivered
with the equipment) on the cutter.
Disconnect the mains plug before starting
any maintenance work.
Sawing chain
Working with a blunt sawing chain causes prema-
ture wear of the chain, the chain wheel and the
cutter. It can also cause the sawing chain to break.
It is therefore important that the sawing chain is
sharpened in good time.
Sharpening should be carried out by a specialist
workshop. The sawing chain cutters have the
following angles: front rake = 85°,
cutting angle = 60°, sharpening angle = 30°.
A 4-mm round file is required to sharpen the
sawing chain.
The Metabo sawing chain sharpening set also
allows you to sharpen the sawing chain yourself.
Before sharpening, read through and follow the
instructions for use enclosed in the sawing chain
sharpening set.
For sawing chain sharpening set or replacement
sawing chains, refer to the chapter on Accesso-
ries.
Cutter
Occasionally, some ball bearing grease must be
applied with a grease gun through the lubrication
holes besides the rivets for the deflector star at the
front end of the cutter.
The lower edge of the cutter is particularly suscep-
tible to wear. To avoid one-sided wear of the
cutter, the cutter should be turned every time the
sawing chain is sharpened.
You should also take this opportunity to clean the
groove and the oil inlet bores (14) of the cutter.
For replacement cutters, refer to the Accessories
chapter.
Chain wheel
If the chain wheel (19) shows signs of wear, it must
be replaced.
After the sawing chain has been replaced twice,
the chain wheel is usually also worn.
See the chapter on Repairs.
Carbon brushes
When the carbon brushes on the chainsaw are
worn, the automatic switch-off system cuts out the
power and the machine comes to a standstill.
See the chapter on Repairs.
Unfavourable power supply conditions can result
in temporary voltage dips.
If the mains impedance at the connection point to
the public mains is greater than 0.3 ohms, further
measures may be required before the machine can
function as specified at this connection. If neces-
sary, enquire about the impedance at your local
power supplier.
Use only genuine Metabo accessories.
If you need any accessories, check with your
dealer.
For dealers to select the correct accessory, they
need to know the exact model designation of your
power tool.
See page 4.
A Sawing chain (as replacement)
B Cutter (as replacement)
C Sawing chain sharpening set
D Chainsaw adhesive oil (biologically degra-
dable)
E Full-vision goggles
F Cutting block for chainsaws
Repairs to electrical tools must be carried out by
qualified electricians ONLY!
Any Metabo power tool in need of repair can be
sent to one of the addresses listed in the spare
parts list.
Drain the oil reservoir before sending in the
chainsaw.
Please enclose a description of the fault with the
power tool.
Metabo's packaging can be 100% recycled.
Scrap power tools and accessories contain large
amounts of valuable resources and plastics that
can be recycled.
These instructions are printed on chlorine-free
bleached paper.
9 Maintenance
10 Troubleshooting
11 Accessories
12 Repairs
13 Environmental Protection
17026724_1207 KT 1441.book Seite 20 Montag, 10. Dezember 2007 2:11 14
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo KT 1441 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo KT 1441 in the language / languages: All languages as an attachment in your email.

The manual is 10,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info