Manual Metabo KHE 96 (page 11 of 80) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

595135

Zoom out

Zoom in

1/80

ENGLISH

ENG

Always hold the machine with both hands using

the handles provided, stand securely and concen-

trate.

Always wear protective goggles, gloves, a dust

mask and sturdy shoes when working with this

tool.

Ensure that the spot where you wish to work is free

power cables, gas lines or water pipes

(e.g.

using a metal detector).

Always work with the tool attached correctly. Pull

on the tool to check that it is seated correctly. (It

must be possible to move the tool a few centime-

tres in an axial direction.)

When working above ground level, make sure that

the area underneath is free.

Do not touch the tool or parts close to the tool

immediately after stopping work because they

may still be extremely hot and could cause skin

burns.

Always lay the power cable away from the back of

the machine.

A damaged or cracked additional handle must be

replaced. Never operate a machine with a defec-

tive additional handle.

Dust from material such as paint containing lead,

some wood species, minerals and metal may be

harmful. Contact with or inhalation of the dust may

cause allergic reactions and/or respiratory

diseases to the operator or bystanders.

Certain kinds of dust are classified as carcinogenic

such as oak and beech dust especially in conjunc-

tion with additives for wood conditioning (chro-

mate, wood preservative). Material containing

asbestos must only be treated by specialists.

- Where the use of a dust extraction device is

possible it shall be used.

- The work place must be well ventilated.

- The use of a dust mask of filter class P2 is

recommended.

Follow national requirements for the materials you

want to work with.

See page 3.

1 Bow handle

2 Front thread for additional handle

3 Clamping knob

4 Tool lock

5 Switch button

6 Additional handle

7 Rear thread for additional handle

8 Metabo VibraTech (MVT): integrated damping

system

9 Trigger

10 Locking button for continuous activation

11 Carbon brush service indicator (lamp signal

for pending carbon brush change)

12 Adjusting wheel for setting the

impact force

and speed

• Three rubber handles provide flexible grip in any

working position

• Metabo VibraTech (MVT): integrated damping

system in the bow and additional handles for

reduced vibrations and less stress on the hands

• Additional handle can be attached to the

housing at 3 different points

• Adjusting wheel for setting the

impact force and

speed.

For working on softer materials such as

brick.

• Lockable switch for convenient operation

during continuous chiselling

• Electronic smooth start-up for precision drilling

• Die cast aluminium gear housing for optimum

heat dissipation and stability

• Service indicator for signalling pending carbon

brush changes

Before plugging in, check to see that the

rated mains voltage and mains frequency,

as stated on the rating label, match with your

power supply.

Always use an extension cable with a minimum

diameter of 1.5 mm

. The extension cable must be

suitable for the machine power rating (see Tech-

nical Specifications). If using a roll of cable, always

roll up the cable completely.

7.1 Assembly of the additional handle

For safety reasons, always use the bow

handle (1) or additional handle (6)

supplied.

MHE 96 and KHE 96:

Release the clamping ring by turning the clamping

knob (3) anticlockwise. Adjust the bow handle (1)

to the required position and angle. Tighten the

clamping knob.

KHE 96:

5Overview

6 Special Product Features

7 Commissioning

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Metabo KHE 96 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6,25 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Metabo KHE 96 Manual

Product: