625638
12
Zoom out
Zoom in
Previous page
1/76
Next page
12
ENGLISH
ENG
When a chisel is fitted, only operate
the machine in the chiselling operating
mode. .
Avoid levering movements of the machine
when a chisel is fitted.
Hammer drilling and chiselling with
clockwise rotation only.
8.4 Selection of direction of rotation
Do not actuate the rotation selector
switch (8) unless the motor has
completely stopped.
Select direction of rotation:
R=clockwise
L = counter-clockwise
8.5 Drill chuck change
When changing chucks make sure that
the spindle is clean. Grease spindle lightly
if required.
Removing the chuck:
Turn chuck lock (3) in direction indicated by arrow
against the stop (a) and pull it off the spindle (b).
Replacing the chuck:
Place chuck onto spindle (5) (a). Turn chuck lock
(3) in direction indicated by arrow (b) until chuck
slides fully onto the spindle, then release the
chuck lock.
Check to see that the chuck is properly seated.
Note:
To keep the spindle from turning while
changing chucks, set the control knob (9) to
chiselling.
8.6 Tool Change with SDS Chuck
Before fitting, clean tool shank and
apply special grease (accessories
order no. 6.31800)! Use only SDS-Plus tools.
Inserting the tool:
Turn the tool while inserting, until it engages.
The tool is automatically locked.
Removing the tool:
Turn tool lock (2) in direction indicated by arrow (a)
and remove the tool (b).
8.7 Tool change with keyless chuck
(accessory)
Use the keyless chuck when non-impact drilling in
metal, wood etc. and driving screws.
Chucking the tool:
Turn sleeve towards "AUF, RELEASE" (a). Insert
tool as deeply as possible (b) and turn sleeve in the
opposite direction, until the noticeable mechanical
resistance is overcome.
Caution! The tool is not
yet clamped!
Keep turning the sleeve
(it must "click" when
turning)
until it cannot be turned any further -
only
now
is the tool
securely
clamped.
With a soft tool shank, retightening may be required
after a short time of drilling.
17024652_0308 KHE 32.book Seite 12 Dienstag, 11. März 2008 11:23 11
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo KHE 32 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo KHE 32 in the language / languages: All languages as an attachment in your email.

The manual is 3,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info