Manual Metabo KHE 2644 (page 8 of 52) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

595378

Zoom out

Zoom in

1/52

ENGLISHen

Before plugging in check to see that the rated

mains voltage and mains frequency, as stated

on the rating label, match with your power supply.

Australia: Always use a residual current device

(RCD) protected supply with a rated residual

current of 30 mA or less.

6.1 Side handle installation

For safety reasons, always use the side

handle supplied.

Open the clamping ring by turning the side handle

(1) counter-clockwise. Place the side handle onto

the machine's collar. Insert the depth stop (3).

Tighten the side handle in the required angle

depending on the task at hand.

7.1 Depth Stop Setting

Loosen the side handle (1). Set depth stop (3) to the

desired drilling depth and retighten the side handle.

7.2 Setting direction of rotation

Do not activate the rotation selector switch (4)

unless the motor has completely stopped.

See page 2.

R = Clockwise setting

L = Counter-clockwise setting

7.3 Operating mode selection

Select the desired operating mode by turning the

control knob (8). To turn, push the stop (7).

Drilling

Hammer drilling

Chiselling

(KHE 2444, KHE 2644 only)

In chiselling mode, the chisel is locked so that it

cannot turn.

To position the chisel for a particular application, set

the switch button (8) between and .

When a chisel is fitted, only operate the

machine in the chiselling operating mode

Avoid levering with the machine when a chisel

is fitted.

7.4 Tool change with SDS chuck

Before fitting, clean tool shank and apply

special grease (accessories order no.

6.31800)! Use only SDS-Plus tools.

Inserting tools:

- Turn tool and insert until it engages. The tool is

locked automatically.

Removing the tool:

See page 2, fig. A.

Pull tool lock (2) backwards in direction indicated by

arrow (a) and remove tool (b).

7.5 Switching on/off, changing speed

Switching on, speed: press the trigger (6).

The speed can be changed by pressing in the

trigger.

Release the trigger to switch off.

Continuous activation: While pressing on the

trigger (6), press in the locking button (5) and

then release the trigger. To switch off, press and

release the trigger (6) again.

In continuous operation, the machine

continues running if it is forced out of your

hands. Therefore, always hold the machine with

both hands using the handles provided, stand in a

safe position and concentrate.

The vent slots of the machine should be cleaned

from time to time.

If the trigger (6) can not be depressed, check to see

that the direction of rotation selector switch (4) is

fully set to the R or L position.

Use only genuine Metabo accessories.

Use only accessories which fulfil the requirements

and specifications listed in these operating instruc-

tions.

Fit accessories securely. Secure the machine if it is

operated in a bracket. Loss of control can cause

personal injury.

For a complete range of accessories, see

www.metabo.com or the main catalogue.

Repairs to electrical tools must be carried out by

qualified electricians ONLY!

Contact your local Metabo representative if you

have Metabo power tools requiring repairs. For

addresses see www.metabo.com.

You can download a list of spare parts from

www.metabo.com.

Observe national regulations on environmentally

compatible disposal and on the recycling of disused

machines, packaging and accessories.

Only for EU countries: Never dispose of

power tools in your household waste! In

accordance with European Guideline

2002/96/EC on used electronic and electric

equipment and its implementation in national

6. Start of Operation

7. Use

8. Maintenance

9. Trouble Shooting

10. Accessories

11. Repairs

12. Environmetal Protection

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Metabo KHE 2644 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,14 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Metabo KHE 2644 Manual

Product: