Manual Metabo KGSM 216 Vario Max (page 17 of 116) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

648373

Zoom out

Zoom in

1/116

ENGLISH en

– adjustment installations

–controls;

– motor vent slots;

– space under table insert;

– cutting laser;

– illumination of cutting line

10.6 Storage of device

Danger!

 Store the device in such a way that it cannot be

put into operation by unauthorised personnel.

 Ensure that the stationary device cannot cause

injury.

Caution!

 Do not store the tool outdoors or in damp

conditions without protection.

10.7 Maintenance

Prior to each use

 Remove saw chips with vacuum or brush.

 Check power cable and power cable plug or

battery pack for damage; if necessary have

damaged parts replaced by a qualified

electrician.

 Check all movable parts if they can be moved

freely across the entire range of movement.

Regularly, depending on conditions of use

 Check all screwed joints, retighten if necessary.

 Check reset function of the saw head (saw head

has to return to the upper starting position by

means of spring force), if required have spring

replaced.

 Slightly oil guide elements.

– Use appropriate supports on the left and right of

the saw for long workpieces.

– Hold workpiece on the right of the saw blade for

suitable cuts.

– When cutting small pieces, use additional guide

(a suitable wooden board attached with screws

to the guide of the device, can be used as

additional guide).

– When cutting a curved (contorted) board (53)

place the convex side at the parallel guide/

ripping fence.

– Do not cut workpiece upright, but flat on the

turntable.

Use only genuine Metabo accessories.

Use only accessories which fulfil the requirements

and specifications listed in these operating

instructions.

A Spray for maintenance and care for the

removal of resin residues and to preserve the

metal surfaces. 0911018691

B Extraction adapter "Multi" for the connection of

extraction hoses with 44, 58 or 100 mm adapter

0910058010

C Metabo all-purpose vacuum cleaner (see

catalogue)

D Stands:

Universal machine stand UMS 6.3131700

Mobile stand KSU 250 Mobile

6.3131800

Stand KSU 400 0910066110

E Roller stand:

RS 420 0910053353

RS 420 G 0910053345

RS 420 W 0910053361

Saw blades for KGS 216 M / KGSV 216 M /

KGSM 216 Vario Max:

F Saw blade Power Cut 6.28009

216 × 2.4 / 1.8 × 30 24 WZ 5° neg

for longitudinal and transverse cuts in solid wood

G Saw blade Precision Cut Classic 6.28060

216 × 2.4 / 1.8 × 30 40 WZ 5° neg

for longitudinal and transverse cuts in solid wood

and chipboard

H Saw blade Multi Cut Classic 6.28066

216 × 2.4 / 1.8 × 30 60 FZ/TZ 5° neg

for longitudinal and transverse cuts in coated

materials, laminate, plastic and aluminium profiles

Saw blades for KGS 254 M:

I Saw blade Precision Cut Classic 6.28061

254 × 30 x 2.4 / 1.8,48 WZ 5° neg

for longitudinal and transverse cuts in solid wood

and chipboard

J Saw blade Multi Cut 6.28223

254 × 30 x 2.4 /1.6, 80 FZ/TZ 5° neg

for longitudinal and transverse cuts in coated

materials, laminate, plastic and aluminium profiles

Saw blades for KGS 305 M:

K Saw blade Precision Cut Classic 6.28064

305 × 30 x 2.4 /1.8,56 WZ 5° neg

for longitudinal and transverse cuts in solid wood

and chipboard

L Saw blade Multi Cut 6.28091

305 x 30 x 2.8/2.0 96 FZ/TZ 5° neg,

for longitudinal and transverse cuts in coated

materials, laminate, plastic and aluminium profiles

Saw blades for KGS 18 LTX 216:

M Saw blade Precision Cut Classic 6.28065

216 × 1.8 / 1.2 × 30 40 WZ 5°

for longitudinal and transverse cuts in solid wood

and chipboard

For a complete range of accessories, see

www.metabo.com or the catalogue.

Danger!

Repair of power tools must be carried out by

qualified electricians only!

If you have Metabo power tools that require

repairs, please contact your Metabo service

centre. For addresses see www.metabo.com.

You can download a list of spare parts from

www.metabo.com.

Observe national regulations on environmentally

compatible disposal and on the recycling of

disused machines, packaging and accessories.

Only for EU countries: Never dispose of

power tools in your household waste! In

accordance with European Directive 2002/

96/EC on waste electrical and electronic

equipment and its implementation in national

legal systems, used power tools must be

collected separately and handed in for

environmentally compatible recycling.

Following you will find a description of problems

and faults that you may remedy yourself. If the

corrective measures described here do not help,

kindly refer to chapter 13. "Repairs".

Danger!

There are particularly many accidents in

connection with problems and faults. Therefore

keep in mind:

 Prior to each correction of faults, pull the mains

plug or remove the detachable battery pack

(34).

 Check that all safety devices are operational

again after each fault service.

No trimming function

Transport lock activated:

 pull out transport lock.

Safety lock activated:

 loosen safety lock.

Cutting power too low

Saw blade blunt (possibly tempering marks on

blade body);

Saw blade unsuitable for the material (see

chapter 12. "Accessories");

Saw blade contorted:

 Replace saw blade (see chapter 10.

"Maintenance").

Saw vibrates a lot

Saw blade contorted:

 Replace saw blade (see chapter 10.

"Maintenance").

Saw blade not installed properly:

 Install saw blade properly (see chapter 10.

"Maintenance").

Turntable hard to turn

Chips under turntable:

 remove chips.

Explanatory notes on the specifications on page 3.

Changes due to technological progress reserved.

U =mains voltage / voltage of battery pack

I=rated power

F =min. fuse protection

=rated input power

IP =protection class

=no-load speed

=max. cutting speed

D =saw blade diameter (outer)

d =saw blade hole (inside)

b = max. tooth width of the saw blade

A =dimensions (lxwxh)

m=weight

Requirements for chip and dust extraction unit:

=connection diameter of the extraction

nozzle

=minimum air throughput

=minimum negative pressure at extraction

nozzle

=minimum air speed at extraction nozzle

Maximum cross-section of workpiece, see table

on page 4.

~ AC Power

Direct current

Machine in protection class II

The technical specifications quoted are subject to

tolerances (in compliance with the relevant valid

standards).

Emission values

These values make it possible to assess the

emissions from the power tool and to compare

different power tools. Depending on the operating

conditions, the condition of the power tool or the

accessories, the actual load may be higher or

lower. For assessment purposes, please allow for

breaks and periods when the load is lower. Based

on the adjusted estimates, arrange protective

measures for the user e.g. organisational

measures.

Typical A-effective perceived sound levels

=sound-pressure level

=acoustic power level

, K

= uncertainty

Wear ear protectors!

11. Tips and Tricks

12. Accessories

13. Repairs

14. Environmental Protection

15. Troubleshooting

16. Technical Specifications

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Metabo KGSM 216 Vario Max in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 27,55 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Metabo KGSM 216 Vario Max Manual

Product: