451439
43
Zoom out
Zoom in
Previous page
1/64
Next page
43
NEDERLANDS
De draaitafel staat in 0° -stand, de
stelschroef voor de draaitafel is
vastgedraaid.
De inclinatie van de kantelarm ten
opzichte van de loodlijn bedraagt 0°,
de grendelhefboom voor de instel-
ling van de inclinatie is vastgezet.
Trekinrichting helemaal achteraan.
De stelschroef van de trekinrichting
is losgedraaid (indien de werkstuk-
breedte dit vereist).
Een werkstuk zagen:
1. Druk het werkstuk tegen de werk-
stukaanslag.
2. Bedien de veiligheidsvergrendeling
en houd de Aan/Uit-schakelaar
ingedrukt.
3. Laat de zaagkop aan de handgreep
langzaam neer.
A
Opgelet!
Bij het zagen de zaagkop enkel
zo vast op het werkstuk draaien, dat
het motortoerental niet te sterk daalt,
omdat anders de motor kan worden
overbelast en beschadigd.
4. Trek bij bredere werkstukken de
zaagkop tijdens het zagen naar voor
(naar de gebruiker toe).
5. Zaag het werkstuk in één beweging
door.
6. Laat de Aan/Uit-schakelaar los en
laat de zaagkop langzaam in de
bovenste uitgangspositie terug-
zwenken.
7. Zaagkop in de achterste positie
terugschuiven.
8.2 Versteksneden
3
Aanwijzing:
Bij het verstekzagen wordt het
werkstuk gezaagd in een hoek ten
opzichte van de achterste aanlegrand.
Maximale doorsnede van het werkstuk
(afmetingen in mm):
Uitgangspositie:
De zaagkop is naar boven
gezwenkt.
De snijdieptebegrenzing is op maxi-
male snijdiepte ingesteld.
De inclinatie van de kantelarm ten
opzichte van de loodlijn bedraagt 0°,
de grendelhefboom voor de instel-
ling van de inclinatie is vastgezet.
Trekinrichting helemaal achteraan.
De stelschroef van de trekinrichting
is losgedraaid.
Een werkstuk zagen:
1. Blokkeerschroef (45) van de draaita-
fel (43) losdraaien en pal (44) los-
maken.
2. Stel de gewenste hoek in.
3
Aanwijzing:
De draaitafel klikt vast in de vol-
gende hoekstanden: 0°, 15°, 22,5°, 30°,
en 45°.
3. Draai de stelschroef van de draaita-
fel vast.
4. Zaag het werkstuk zoals beschre-
ven onder "Rechte sneden".
8.3 Schuine sneden
3
Aanwijzing:
Bij het schuin zagen wordt het
werkstuk gezaagd in een hoek ten
opzichte van de loodlijn.
Maximale doorsnede van het werkstuk
(afmetingen in mm):
Uitgangspositie:
De zaagkop is naar boven
gezwenkt.
De snijdieptebegrenzing is op maxi-
male snijdiepte ingesteld.
De draaitafel staat in 0° -stand, de
stelschroef voor de draaitafel is
vastgedraaid.
Breedte ca. Hoogte ca.
Stand draaitafel
15° 246 60
22,5° 235 60
30° 220 60
45° 177 60
47° - 0°
0° - 47°
Breedte ca. Hoogte ca.
Inclinatie
kantelarm
22,5° 255 53
45° 255 30
43 44 45
0° - 45°
43


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Metabo KGS 255 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Metabo KGS 255 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 7,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Metabo KGS 255

Metabo KGS 255 User Manual - Danish - 58 pages

Metabo KGS 255 User Manual - Portuguese - 64 pages

Metabo KGS 255 User Manual - Swedish - 58 pages

Metabo KGS 255 User Manual - Spanish - 64 pages

Metabo KGS 255 User Manual - Norwegian, Finnish - 58 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info