Manual Metabo KFM 9-3 RF (page 11 of 108) (All languages)

625653

Zoom out

Zoom in

1/108

ENGLISH en

Original instructions

We, being solely responsible: Hereby declare that

these bevelers, identified by type and serial number

*1), meet all relevant requirements of directives *2)

and standards *3). Technical documents for *4) -

see page 3.

The beveler is intended for the bevelling of edges of

steel, stainless steel, aluminium and aluminium

alloys in the professional sector.

For processing aluminium, aluminium alloys and

stainless steel, a suitable lubricant (item no.:

6.23443) must be used.

The user bears sole responsibility for any damage

caused by inappropriate use.

Generally accepted accident prevention

regulations and the enclosed safety information

must be observed.

For your own protection and for the

protection of your power tool, pay

attention to all parts of the text that are

marked with this symbol!

WARNING – Reading the operating

instructions will reduce the risk of injury.

WARNING Read all safety warnings and

instructions. Failure to follow all safety

warnings and instructions may result in electric

shock, fire and/or serious injury.

Keep all safety instructions and information for

future reference.

Pass on your power tool only together

with these documents.

a) Do not use accessories that are not

specifically designed and recommended for

this power tool by the manufacturer. Just

because the accessory can be attached to your

power tool, it does not assure safe operation.

b) Do not use damaged power tools. Before

use, check the indexable inserts for chipping,

cracks, or signs of severe wear and tear. If a

power tool or accessory is dropped, inspect for

damage or install an undamaged accessory.

c) User personal protective equipment.

Depending on application, use face shield,

safety goggles or safety glasses. As

appropriate, wear dust mask, hearing

protectors, gloves and workshop apron

capable of stopping small abrasive or

workpiece fragments. The eye protection must be

capable of stopping flying debris generated by

various operations. The dust mask or respirator

must be capable of filtrating particles generated by

your operation. Prolonged exposure to high

intensity noise may cause hearing loss.

d) Keep bystanders a safe distance away from

work area. Anyone entering the work area must

wear personal protective equipment. Fragments

of workpiece or of a broken accessory may fly away

and cause injury beyond immediate area of

operation.

e) Always hold the tool firmly in your hands

during the start-up. The reaction torque of the

motor, as it accelerates to full speed, can cause the

tool to twist.

f) Use clamps to support workpiece whenever

practical. Never hold a small workpiece in one

hand and the tool in the other hand while in

use. Clamping a small workpiece allows you to use

your hands to control the tool.

g) Never lay the power tool down until the

accessory has come to a complete stop. The

spinning accessory may grab the surface and pull

the power tool out of your control.

h) Do not run the power tool while carrying it at

your side. Accidental contact with the spinning

accessory could snag your clothing, pulling the

accessory into your body.

i) Regularly clean the power tool’s air vents. The

motor’s fan will draw the dust inside the housing and

excessive accumulation of powdered metal may

cause electrical hazards.

j) Do not operate the power tool near flammable

materials. Sparks and hot chips can ignite these

materials.

k) Do not use accessories that require liquid

coolants. Using water or other liquid coolants may

result in electrocution or shock.

4.1 Kickback and Related Warnings

Kickback is the sudden response to an accessory

pinching or jamming while rotating. Pinching or

snagging causes rapid stalling of the rotating

accessory, Pinching or snagging causes rapid

stalling of the rotating accessory which in turn

causes the uncontrolled power tool to be forced in

the direction opposite of the accessory’s rotation at

the point of the binding.

For example, if an indexable insert is snagged or

pinched by the workpiece, the edge of the insert that

is entering into the pinch point can dig into the

surface of the material causing the insert to climb

out or kick out. The indexable insert may either jump

toward or away from the operator, depending on

direction of the indexable insert holder at the point

of pinching. Indexable inserts may also break under

these conditions.

Kickback is the result of power tool misuse and/or

incorrect operating procedures or conditions It can

be prevented if suitable precautionary measures

are taken as described below.

1. Declaration of Conformity

2. Specified Use

3. General Safety Instructions

4. Special Safety Instructions

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Metabo KFM 9-3 RF in the language / languages: All languages as an attachment in your email.

The manual is 10,06 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Metabo KFM 9-3 RF Manual

Product: